To Next Page

To Previous Page

AS 8000 Autosampler . 85

Error Messages from the DSC 6000

Error message ID Error Possible Cause Corrective

Action

ERR_DUE_TO_AUTOSAMPLER AS 8000 entered

fatal error state.

This caused DSC

to enter fatal

error state

Refer to AS 8000

error message

Refer to AS 8000

troubleshooting

(above)

ERR_AUTOSAMPLER_RESPONS Timeout on

command.

Response from

command

transmitted to AS

8000

I2C connection

cable defective

Replace I2C cable

ERR_AUTOSAMPLER_I2C_WD No link between

DSC and AS 8000

via I2C

I2C connection

cable defective

Replace I2C cable

Table of Contents3
Introduction5
Pyris Installation6
Safety and Regulatory Information7
Symbols Used in Online Help8
Notes, Cautions and Warnings8
Symbols Used on the Instruments11
Electrical Warnings12
General Warning14
Electromagnetic Compatibility (EMC)15
Europe15
South Korea15
United States (FCC)15
Electrical Safety16
Pollution Degree 216
WEEE Instructions for Perkinelmer Products17
Prepare the Laboratory19
Prepare the Laboratory20
Electrical Requirements20
Environmental Requirements20
Purge Gas and Pneumatic Supply21
Space Requirements21
Install Multiple Analyzers23
Install Multiple Analyzers24
Install a DSC 600027
Safety Precautions for the DSC 600028
Decontamination and Cleaning31
Decontamination31
Cleaning the Instrument31
General Laboratory Safety31
DSC 6000 Warning Labels32
Warning Labels on the Upper Ring Around the Furnace32
Warning Labels on the Back of the DSC 600034
Install a DSC 600036
Unpacking the DSC 600037
Unpacking the Cryofill LN2 Dewar38
Set up the DSC 6000 System Components39
Select the Correct Voltage for the DSC 600039
Connect the Purge Gas Supply to the DSC 600041
Connect the Purge Gas and System Purge Gas Lines to the DSC 600042
Connect the Cooling Device to the DSC 600042
Connect the DSC 6000 System Components48
Configure the DSC 600049
Starting the Pyris Manager50
Calibrate the DSC 600051
DSC 6000 Hardware55
Dsc 600056
Furnace and Sensor Design56
Cooling57
Calibration of the DSC 600058
Temperature Calibration58
Perform Indium and Zinc Runs59
Perform a Peak Area with Onset Calculation59
Performing a Temperature Calibration60
Heat Flow Calibration60
Operating Variables and Sample Handling62
Temperature Range62
Scanning Rate62
Subambient Operation of the DSC 600063
DSC 6000 Maintenance64
DSC 6000 Part Numbers65
Miscellaneous Part Numbers66
AS 8000 Autosampler67
AS 8000 Autosampler68
Safety Precautions for the as 800070
How the as 8000 Autosampler Works71
Autosampler Work Cycle71
Reduced Time Cycle73
AS 8000 Autosampler Gripper Alignment74
AS 8000 Sample Handling75
Sample Preparation75
Sample Pans75
Sample Loading75
Running a Play List with the as 800078
Troubleshooting82
Error Messages from the DSC 600085
AS 8000 Autosampler Maintenance86
Cleaning and Decontamination86
Install a Reference Pan in a DSC 4000, DSC 6000, Pyris 6 DSC or Jade DSC with as 8000 Autosampler87

Brand	PerkinElmer
Model	DSC 6000
Category	Measuring Instruments
Language	English

PerkinElmer DSC 6000 User Manual

Table of Contents

Questions and Answers:

PerkinElmer DSC 6000 Specifications

Related product manuals