PFlow Industries D116 User Manual

Revision: 3.0.3
Example1: To enter a pipe
outside diameter of 219.234, the
procedure is as follows:
Press
keys to enter Window M11 (the
numerical value displayed currently is a previous value). Now
press key. The symbol ">"
and the flashing cursor are
displayed at the left end of the second
line on the Screen.
input the parameters; or do not press the
.
You can check the selected option by visiting Option T
Windows. If you want to modify it, you must press
the symbol ">"
and the flashing cursor are displayed at the left
of the Screen. Operator can use the
and
the screen and get the required value then press
confirm; or enter the corresponding value option directly and
press to confirm.
For example, if
the pipe material is "Stainless
to enter Window M14, press
the options. Select the "1. Stainless Steel" option by pressing
and , then press
to confirm the
possible to press
key to change the selection
until "1.Stainless Steel" is displayed on the second line of
screen, then press to confirm.
Attention
Generally, press
key first if operator wants to enter
possible even after pressing the
"Unlock" it, select "Unlock"
in Window M47 and enter the original password.
1.6
Flowmeter Window Descriptions
These windows are assigned as follows:
01~08
Flow Totalizer Display: to display flow rate, positive total, negative total, net total, velocity, date &
time, present operation and flow results today, etc.
10~29
Initial Parameter Setup: to enter pipe outside diameter, pipe wall thickness, fluid type,
transducer mounting method
and spacing, etc.
30~38 Flow Units Options:
to select the flow unit such as cubic
on/off and reset totalizers, etc.
40~49
Setup options: Scaling factor, system lo
55~89 Input and output setup:
date and time, ESN, communication baud rate setting, etc.
90~98
Diagnoses: Signal strength and signal quality (Window M90), TOM/TOS*100 (Window M91), flow
sound velocity (Window M92), total time and
(Window M94), etc.
+0~+5
Appendix: power on/off time, total working hours, on/off times and a single
Attention
The other windows for hardware adjustment
Menu
1 1
Enter
Enter
2
1
9
●
2
3
4 5 Enter
^
Enter
Menu
1
4
^
^
Enter
1
Enter
Enter
D116
Series Ultrasonic Flowmeter
outside diameter of 219.234, the
keys to enter Window M11 (the
numerical value displayed currently is a previous value). Now
and the flashing cursor are
line on the Screen.
Then
key, directly enter
You can check the selected option by visiting Option T
ype
Windows. If you want to modify it, you must press
first,
and the flashing cursor are displayed at the left
and
to scroll
the screen and get the required value then press
to
confirm; or enter the corresponding value option directly and
the pipe material is "Stainless
Steel", Press
to enter Window M14, press
to modify
the options. Select the "1. Stainless Steel" option by pressing
to confirm the
selection; It is
key to change the selection
and wait
until "1.Stainless Steel" is displayed on the second line of
the
key first if operator wants to enter
"modify" status. If the "
modify
possible even after pressing the
key, it means that system is locked by a password. To
in Window M47 and enter the original password.
Flowmeter Window Descriptions
Flow Totalizer Display: to display flow rate, positive total, negative total, net total, velocity, date &
time, present operation and flow results today, etc.
Initial Parameter Setup: to enter pipe outside diameter, pipe wall thickness, fluid type,
and spacing, etc.
to select the flow unit such as cubic
meter, liter or other
units, can
Setup options: Scaling factor, system lo
ck (Window M47), etc.
date and time, ESN, communication baud rate setting, etc.
Diagnoses: Signal strength and signal quality (Window M90), TOM/TOS*100 (Window M91), flow
sound velocity (Window M92), total time and
delta time (Window M93), Reynolds number and factor
Appendix: power on/off time, total working hours, on/off times and a single
-
accuracy function calculator.
The other windows for hardware adjustment
are reserved by the manufacturer.
Enter
Pipe Outer Diameter
>_
Enter
^
Enter
Enter
Pipe Material [14
>
1. Stainless Steel
Enter
Series Ultrasonic Flowmeter
Page 10 of 53
modify
" is still not
key, it means that system is locked by a password. To
Flow Totalizer Display: to display flow rate, positive total, negative total, net total, velocity, date &
Initial Parameter Setup: to enter pipe outside diameter, pipe wall thickness, fluid type,
transducer type,
units, can
turn totalizers
Diagnoses: Signal strength and signal quality (Window M90), TOM/TOS*100 (Window M91), flow
delta time (Window M93), Reynolds number and factor
accuracy function calculator.
Pipe Outer Diameter
Pipe Material [14
1. Stainless Steel

PFlow Industries D116 Specifications

General

Brand	PFlow Industries
Model	D116
Category	Measuring Instruments
Language	English