Precor C556 - Page 57

To Next Page

To Previous Page

C556, C556i Navy Self Powered Elliptical Fitness

Page 57

5. Align the lower pivot arm with the handlebar and replace the bolt removed in step 2. Torque

the bolts to 156 inch pounds.

Main Page

Section One - Things You Should Know2
General Information4
Tools Required4
Section Two - Preventive Maintenance5
Daily Maintenance5
Weekly Maintenance5
Quarterly Maintenance6
Procedure 3.1 - Software Access Codes7
Procedure 3.2 - Accessing the Diagnostic Program8
Procedure 3.3 - Displaying the Odometer9
Procedure 3.4 - Club Settings10
Procedure 3.5 - Documenting Software Problems11
Procedure 5.1 - Measuring the Resistance of a Generator (C556 Navy, Only)13
Procedure 5.2 - Measuring the Resistance of a Generator (C556I Navy, Only)14
Procedure 5.3 - Inspecting and Adjusting Belt Tension16
Procedure 6.1 - Troubleshooting the Lower and Upper Interconnect Cable19
Procedure 6.2 - Troubleshooting the Keypad and Upper PCA21
Procedure 6.3 - Upper Display Does Not Illuminate (C556 Navy, Only)23
Procedure 6.4 - Upper Display Does Not Illuminate (C556I Navy, Only)25
Procedure 6.5 - Troubleshooting the Generator (C556 Navy)27
Procedure 6.6 - Troubleshooting the Generator (C556I Navy, Only)28
Procedure 7.1 - Replacing the Display Enclosure or Upper PCA29
Section One, Things You Should Know29
Keypad Connector30
Procedure 7.3 - Replacing the Lower PCA (C556I Navy, Only)33
Procedure 7.4 - Replacing a Lower or Upper Interconnect Cable35
Procedure 7.5 - Replacing a Crankarm Assembly37
Procedure 7.6 - Replacing the Input Pulley Belt39
Procedure 7.7 - Replacing the Generator Pulley Belt40
Procedure 7.8 - Replacing the Input Pulley Assembly42
Procedure 7.9 - Replacing the Step-Up Pulley Assembly44
Procedure 7.10 - Replacing a Wheel Assembly45
Procedure 7.11 - Replacing a Stairarm Pedal47
Procedure 7.12 - Replacing a Stairarm (C556 Navy, Only)48
Procedure 7.13 - Replacing a Stairarm (C556I Navy, Only)50
Procedure 7.13 - Replacing a Ramp Assembly52
Procedure 7.14 - Replacing a Handlebar54
Procedure 7.15 - Replacing a Lower Pivot Arm (C556 Navy, Only)56
Procedure 7.16 - Replacing Handlebar Linkage (C556I Navy, Only)58
Procedure 7.17 - Replacing an Upper Pivot Arm59
Procedure 7.18 - Replacing a Main Column60
Procedure 7.19 - Replace the Rear Cover62
Procedure 7.20 - Replacing a Load Resistor64
Procedure 7.21 - Replacing a Generator (C556 Navy, Only)66
Procedure 7.22 - Replacing a Generator (C556I Navy, Only)68
Procedure 7.23 - Replacing a Battery (C556 Navy, Only)70
Procedure 7.24 - Replacing a Battery (C556I Navy, Only)72
Procedure 7.25 - Replacing a Power Input Jack Assembly74
Procedure 7.26 - Replacing a Frame Tube75
Procedure 7.27 - Replacing a Ramp Support76
Procedure 7.28 - Replacing a Ramp Mounting Bracket78
Procedure 7.29 - Replacing a Stairarm Pivot Block (C556 Navy, Only)80
Procedure 7.30 - Replacing the PROM82
Wiring Diagram 8.1 - C556 Navy Self Powered83
Block Diagram 8.2 - C556 Navy Self Powered84
Wiring Diagram 8.3 - C556I Navy Self Powered85
Block Diagram 8.4 - C556I Navy Self Powered EFX86

Precor C556 - Page 57

Table of Contents

Related product manuals