Primera LX400 - User Manual

Other manuals for Primera LX400

Quick Start Guide2 pages

Questions and Answers

S
Sara DavisAug 15, 2025
What to do if Primera Label Maker has reduced print quality?
- N
  Nancy TranAug 15, 2025
  To address reduced print quality or a potentially clogged cartridge nozzle in your Primera Label Maker, follow the steps to clean the ink cartridge nozzles.
A
Angela McmillanAug 18, 2025
Why is the image vertically offset on Primera LX400 Label Maker?
- R
  ruizjoshuaAug 18, 2025
  If the image is vertically offset when printing with your Primera Label Maker, consider these potential causes and solutions: * **TOF Offset:** Increase this setting to move the image down or decrease it to move the image up on the label. * **Nonstandard/Non-translucent Backing Material:** Test with the sample material that came with the unit to check compatibility. * **Page Size:** Ensure the page size set in the driver isn't larger than the label stock to prevent ink from printing on the gaps. * **Portrait/Landscape:** Verify this setting is correct. * **Sensor Position:** Consult Section 2F if using circular or non-rectangular die-cut labels.
C
Carlos LynnAug 21, 2025
Why is the image printing horizontally offset on Primera Label Maker?
- W
  westsoniaAug 21, 2025
  If the image is printing horizontally offset on your Primera Label Maker, it could be due to: * **Left Margin Offset:** If there’s white space on the right side of the label and overlap on the opposite side, decrease the number. * **Page Size:** Increase the page size through the printer preferences enough to cover the label.
A
Amber BushAug 25, 2025
How to make the image cover the entire label on Primera LX400?
- D
  Dr. Denise FloresAug 26, 2025
  To ensure the image covers the entire label on your Primera Label Maker, make the image a few millimeters larger than the label by dragging the image over the edge of the label on all sides.
A
Amanda BrownAug 28, 2025
What to do if there is a label jam in Primera Label Maker?
- C
  campbelljosephAug 28, 2025
  If a label jam occurs in your Primera Label Maker, open the cover and remove the jammed label from the printer feed output area.
C
Crystal ThomasAug 31, 2025
Why is the image vertically offset on my Primera LX400?
- T
  Timothy BenjaminAug 31, 2025
  The image may be vertically offset due to several reasons. The TOF Offset may need fine tuning. Increase the setting to move the image down or decrease it to move the image up. Also, the label stock may not be compatible if you are using nonstandard or non-translucent backing material. Test with the sample material that came with the unit, or try label stock with a black mark on the back.
T
tracy59Sep 4, 2025
How to fix reduced print quality on Primera LX400 Label Maker?
- W
  willieandersonSep 4, 2025
  To address reduced print quality, follow these steps: Remove the print cartridge. Moisten a lint-free cloth with water. Hold the cloth against the nozzles for three seconds. Wipe in one direction only. Repeat the process.
H
huffmansarahSep 7, 2025
Why is the image printing horizontally offset on my Primera LX400?
- B
  brownoliviaSep 7, 2025
  If the image is printing horizontally offset, and you notice white space on the right side of the label and overlap on the opposite side, decrease the number. Alternatively, increase the page size through the printer preferences enough to cover the label.
B
burnsraymondSep 12, 2025
How to clean ink off the printer casing of Primera LX400 Label Maker?
- R
  Regina JonesSep 12, 2025
  If ink gets on the printer casing, clean it with an ammonia-based window cleaner and a lint-free cloth.