Protec COMPACT 2 NDT - Page 5

COMPACT 2 NDT
User Manual
519
0
-
0
-
0002
PROTEC GmbH & Co. KG, In den Dorfwiesen 14, 71720 Oberstenfeld, Germany
5
von
65
6.2.4 Thorough Cleaning .......................................................................................................................................................... 34
6.2.5 Before you go on holiday or longer than 2 weeks not use ..................................................................... 35
6.3 Check-up and maintenance ................................................................................................................................................... 35
6.3.1 Recommended Maintenance Work....................................................................................................................... 35
6.3.2 Maintenance ........................................................................................................................................................................ 36
6.3.3 Maintenance Protocol .................................................................................................................................................... 37
6.4 Warranty .............................................................................................................................................................................................. 38
6.5 Product life time ............................................................................................................................................................................. 38
6.6 Further Information ...................................................................................................................................................................... 38
6.7 Disposal................................................................................................................................................................................................ 38
7 Trouble Shooting............................................................................................................... 39
7.1 Algae ...................................................................................................................................................................................................... 39
7.1.1 Excessive algae growth in water tank................................................................................................................... 39
7.2 General ................................................................................................................................................................................................. 39
7.2.1 Mains switch “ON” – no function............................................................................................................................. 39
7.2.2 No display but circulation pumps run.................................................................................................................. 39
7.3 Drive ....................................................................................................................................................................................................... 39
7.3.1 Machine does not start automatically .................................................................................................................. 39
7.3.2 Machine doesn't stop automatically ..................................................................................................................... 39
7.3.3 Drive motor does not run ............................................................................................................................................ 40
7.3.4 Display shows error message “E2” .......................................................................................................................... 40
7.4 Baths ...................................................................................................................................................................................................... 40
7.4.1 No circulation in bath ..................................................................................................................................................... 40
7.4.2 Developer bath temperature is not reached ................................................................................................... 40
7.4.3 Developer bath temperature is higher than the set temperature, display shows two
crossbars, developer temperature button blinks .................................................................................................................. 40
7.4.4 Developer bath temperature too high or too low (display shows values of 20 °C or 42
°C) 40
7.4.5 Calibration of bath temperature / actual bath temperature is different from displayed
value 40
7.4.5.1 Calibration process..................................................................................................................................................... 40
7.5 Film defects ....................................................................................................................................................................................... 41
7.5.1 Films will not dry................................................................................................................................................................ 41
7.5.2 The film does not transport correctly ................................................................................................................... 41
7.5.3 Scratches, pressure marks, dirt on film ................................................................................................................. 41
7.6 Replenishment ................................................................................................................................................................................ 41
7.6.1 Replenishment pump does not work or works insufficiently................................................................ 41
7.7 Dryer ...................................................................................................................................................................................................... 41
7.7.1 Display shows error message “E4” .......................................................................................................................... 41
7.7.2 Dryer ventilation does not function, no water inflow when water cock opened ..................... 41
7.7.3 Dryer ventilation is too weak...................................................................................................................................... 42
7.7.4 Dryer temperature cannot be reached................................................................................................................ 42
7.7.5 Dryer temperature display exceeds the set value......................................................................................... 42
7.7.6 Dryer temperature cannot be reached or is too high (display shows values approx. 30 °C
and 75 °C) 42
7.8 Water ..................................................................................................................................................................................................... 42
7.8.1 Rinsing water does not flow ....................................................................................................................................... 42
7.8.2 Water tank overflows ...................................................................................................................................................... 42
8 Spare Parts and schematics ............................................................................................. 43
8.1 Spare Parts.......................................................................................................................................................................................... 43
8.2 Spare parts COMPACT 2 Mammo........................................................... Fehler! Textmarke nicht definiert.
8.3 Tips and Tricks.................................................................................................................................................................................. 48
8.3.1 Removal of control PCB ................................................................................................................................................. 48
8.3.2 Adjusting the software – sub-versions ................................................................................................................ 48
8.3.3 Stop start-cycle ................................................................................................................................................................... 48
8.3.4 Display of machine information............................................................................................................................... 48
8.4 Schematics ......................................................................................................................................................................................... 49