What does ATE Call Fail 100 mean on my Pyronix PCX 46 Security System?
This is only operative if the Site Option "ATE Input" is set to 'UK STU.' Check the voltage on the input; if it is +5/12 volts, the device connected is showing a fault.
What does BATTERY FAULT mean on my Pyronix PCX 46 Security System?
This indication is normal during recharge after a mains failure.
What to do if 485/COMMS are lost on my Pyronix PCX 46?
This can occur during routine initialisation. However, if it persists, check the display on other keypads to determine if the failure is isolated to a single keypad or a complete system BUS failure. You might also temporarily install an additional keypad to troubleshoot.
What does 'FUSE x FAULT' mean on my Pyronix PCX 46 Security System?
This message indicates that the identified fuse has failed, or the output protected by the fuse is drawing excessive current. Note that Fuse 1 protects PGMs, Fuse 2 protects the BELL, Fuse 3 protects AUX, Fuse 4 protects the BUS, and Fuse 5 protects the BATTERY.
How to fix a BELL TAMPER error on my Pyronix PCX 46 Security System?
Check that Terminal TR should be at or near 0v. If it is not, check if the Bell Tamper switch is closed. Also, verify that Fuse F2 is intact and check the connections to the SAB.
How do I fix a CALL FAIL TO ARC error on my Pyronix PCX 46?
Check that ALL call details are programmed correctly. Ensure that the signalling format is correctly set for the ARC receiver.
What should I do if there is code guessing on my Pyronix PCX 46 Security System?
Press the X key to clear the code guessing attempt.
What does ATE LINE FAULT mean on my Pyronix Security System?
This is only operative if the Site Option "ATE Input" is set to 'UK STU' or 'ATE Line Fault.' Check the voltage on the input pin; if it is +5/12 volts, the connected device is showing a fault. Note that the 'Line Fault' timer is operative.
What does LOW VOLTS mean on my Pyronix Security System?
During a mains failure, the battery volts are below the normal ‘battery fault’ level.
What to do if there is a BELL Fault on Pyronix Security System?
Correct the fault at the warning device to restore the output.
General| Wired zones | 8 |
|---|---|
| Wireless zones | 38 |
| Backup Battery | 7Ah |
| Humidity | 95% non-condensing |
| Operating Temperature | -10°C to +40°C |
Overview of PCX46 as a hybrid alarm system with automation and SMS.
Details on PCX46's high-security wireless system with encryption.
Information on learning up to 32 keyfobs and their status indication.
Ability to operate up to 30 user automation outputs for external devices.
Real-time SMS notifications for system activations and events.
Remote control capabilities via a smartphone application.
Explanation of devices used for arming/disarming: keypad, tag reader, keyfob.
Functions of specific buttons on the keypad (A, B, C, D, 1-3, X, ✓).
Guide on navigating menu systems using keypad buttons.
Explanation of the meaning of LEDs on the keypad (OK, Ready, Alarm, etc.).
Instructions on how to lock and unlock keyfob buttons to prevent accidental presses.
Details on customizing keyfob buttons for functions like arming/disarming.
Method to arm the system immediately by pressing the keyfob button again.
Step-by-step process for arming the system using the keypad and selecting areas.
Steps for arming the system by presenting a tag to the reader.
How to arm the system using a programmed keyfob button.
Process for disarming the system using the keypad and deselecting areas.
Steps for disarming the system by presenting a tag to the reader.
How to disarm the system using a programmed keyfob button.
Visual representation of disarmed and armed states using a tag reader.
Using a tag reader to unlock entry doors and control system arming.
Detailed instructions for arming/disarming using an external tag reader.
Commands to arm the PCX 46 system remotely via SMS.
Commands to disarm the PCX 46 system remotely via SMS.
SMS commands to arm the system while bypassing specific inputs.
SMS commands to bypass specific inputs for the next arming procedure.
SMS command to check the current status of the PCX 46 system.
SMS commands to control user automation outputs like gates and lights.
SMS command to retrieve the status of user automation outputs.
SMS command to change the programmed mobile number for SMS alerts.
SMS command to initiate data upload/download with the PC1.
Steps to download and install the Pyronix SMS control mobile application.
Overview of the application's interface, icons, and default operations.
How to configure panel information, input names, language, and security password.
Process of choosing and executing commands for the PCX control panel via the app.
Visual examples of the application's screens during operation.
How to enable, disable, or toggle the chime feature on keypads.
Note against using chime for wireless detectors due to battery drain.
Instructions for activating a Personal Attack (PA) alarm from the keypad.
Instructions for activating a Fire alarm from the keypad.
Disables sensors for the current arm period, also disables tamper alarms.
Activates/deactivates user automation outputs for remote control of devices.
Programmes user codes, tags, and learns keyfobs for the PCX 46.
Allows testing of all system inputs, siren, and strobe.
Connects to a PC for programming information using InSite UDL software.
Prevents remote arming/disarming and remote dialling for upload/download.
Flowchart for bypassing inputs, allowing selection of specific inputs.
Flowchart for operating user automation outputs, selecting and controlling outputs.
Compensates for clock drift by adjusting minutes gained or lost.
Option to enable or disable automatic summertime adjustments.
Flowchart for configuring user codes, including user type, areas, and arming options.
Process for changing the master manager code for system access.
Flowchart for configuring user codes and learning proximity tags, including area choice.
Process for learning keyfobs and assigning actions to their buttons.
Note on activating PA alarms on keyfobs by pressing two buttons together.
Flowchart for reviewing the panel log, including alarm events.
Flowchart for reviewing access and control logs, like user door openings.
Configuration of SMS numbers, noting reservation for ARC and SMS messaging.
Procedure for performing a walk test on all programmed system inputs.
Procedure for testing the external siren and strobe.
Options for connecting to a PC, selecting dial, data transfer, and diagnostics.
Controls engineer access to the menu, requiring authorization.
Prevents attempts to arm/disarm the system remotely via UDL software.
Prevents attempts to dial into the panel for upload/download operations.
Methods to exit the Master Manager Menu, including using the 'A' key.
Fields for recording alarm company, installation date, site reference, and engineer details.
Table listing wired/wireless inputs 1-32, their names, areas, and descriptions.
Table listing wired inputs 33-46, their names, areas, and descriptions.
Table for assigning user codes, tags, and keyfobs to users.
Table listing wired outputs like PGM and BELL with configuration fields.
Table listing wired outputs from RIX and ATE modules.
Table for configuring wireless outputs like BELL and STRB.
Information on recycling electrical products and disposing of batteries.
To Next Page
