To Next Page

To Previous Page

BIOS LOADING BIOS DEFAULTS

3-14

Loading BIOS Defaults

Different mechanisms exist for resetting the system configuration to the default values.

When a request to reset the system configuration is detected, the BIOS loads the default

system configuration values during the next POST. The request to reset the system to the

defaults can be sent in the following ways:

 A request to reset the system configuration can be generated by pressing <F9> from

within the BIOS Setup utility

 Load BIOS defaults by jumper on the mainboard.

Table of Contents2
Connectors11
About the System12
Introduction13
Package Contents16
A Tour of the System17
- System Overview17
- LED Definitions23
Safety Measures26
Power Supply Unit27
- Removing the Redundant Power Supply Unit27
- Installing the Power Supply Unit28
HDD Tray29
- Releasing the HDD Tray29
- Securing a HDD Tray30
Hot-Plug HDD31
- Hot-Plug HDD Assembly Overview31
- Removing a HDD Carrier and HDD from the HDD Tray32
- Installing a HDD Carrier with HDD to HDD Tray34
Top Cover36
- Removing the Top Cover36
- Installing the Top Cover36
Fan Module38
- Removing a Fan Module38
- Installing a Fan Module39
Memory Modules41
- General Guidelines41
- Memory Population Support41
- Removing a Memory Module41
- Installing a Memory Module42
Processor Heat Sink44
- Removing a Processor Heat Sink44
- Installing a Processor Heat Sink44
Processor46
- Removing the Processor46
- Installing the Processor47
Expansion Card49
- Removing a Riser Assembly49
- Installing a Riser Assembly50
OCP Mezzanine Board51
- Removing a OCP Mezzanine Board51
- Installing an OCP Mezzanine Board52
  - Bios57
BIOS Setup Utility58
- Operation58
- Setup Page Layout58
- Entering BIOS Setup58
- Keyboard Commands59
- Menu Selection Bar60
- Server Platform Setup Utility Screens61
- Main Screen61
- Advanced Screen62
  - Intelrcsetup Screen64
- Server Management Screen65
- Boot Options Screen67
- Security Screen68
- Exit Screen69
- Loading BIOS Defaults71
BIOS Update Utility72
- AFULNX: V2.3972
- ME Region Update72
- BIOS Setting Utility73
- BIOS Revision73
- Clear CMOS73
- Clear Password73
- BIOS Update Via BMC Instructions (Optional)74
Server Management75
- Console Redirection75
- Network BIOS Support77
  - PXE Boot77
- Checkpoints77
  - Debug Header77
  - Bmc79
Server Management Software80
- Server System Overview80
- BMC Key Features and Functions80
- Power System80
- Front Panel User Interface81
- LAN Interface81
  - Session and User82
- Serial over LAN82
- Time Sync82
- Sel82
- Platform Event82
  - Platform Event Filter82
- BMC Firmware Update83
  - DOS Recovery Utility83
  - Webui Update83
BMC Recovery84
- Recovery Process in DOS System84
- Recovery Process in Linux System84
- Recovery Process in Windows System84
Smash85
- System Level Commands86
- BMC Information90
Web Graphical User Interface (GUI) for ESMS92
- Using the Web GUI92
- Login92
- Dashboard93
- Server Information95
- FRU Information96
- Configuration Group105
- Snmp139
- UTC Timezone139
- LAN Port Settings140
- Remote Control141
  - Console Redirection141
  - Server Power Control149
- Maintenance Group149
- Log out154
- User Privilege154

Brand	QCT
Model	QuantaGrid D51PH-1ULH
Category	Network Storage Server
Language	English

QCT QuantaGrid D51PH-1ULH User Manual

Table of Contents

Questions and Answers:

QCT QuantaGrid D51PH-1ULH Specifications

Related product manuals