RADWAG AS series - Page 2

RADWAG AS series

75 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

2

MARCH 2009

Table of Contents

Default Chapter3
- Table of Contents3
1 Technical Data6
2 Basic Information8
- Intended Use8
- Inappropriate Use8
- Warranty8
- Monitoring the Metrological Parameters of the Instrument8
- Data Included in this User Manual8
- Staff Training9
3 Transport and Storage9
- Acceptance Check9
- Packaging9
4 Unpacking, Installation and Commissoning9
- Installation and Operation Place9
- Unpacking10
- Positioning11
- Standard Accessories12
- Cleaning12
- Connection to Mains12
- Connection of Additional Equipment12
5 Basic Functions of the Instrument12
6 Keyboard14
7 User Menu15
- Moving in User Menu17
  - Balance Keyboard17
  - Return to Weighing Function17
8 Weighing18
- Choice of Basic Weighing Unit19
- Choice of Weighing Unit (Temporary)20
- Setting Accessibility of Balance Operating Modes20
  - Choice of Modes Quantity Accessible for User21
  - Setting Contents of P6.1 Ffun - ALL Parameters22
9 Main Setting Parameters23
- Setting Level of Filtering24
- Result Confirmation25
- Autozero Function26
- Light off the Last Display Digit27
10 Another Parameters28
- Backlight of Weighing Result28
- Beep" Signal - Reaction on Pressing Key29
- Printout of All Balance Parameters through RS 232 Port29
11 Balance Calibration30
- Balance with Internal Calibration30
- Entering Calibration Menu32
- Calibration Test35
  - Balances with Internal Calibration35
  - Balances with External Calibration36
- Manual Calibration37
  - Internal Calibration37
  - External Calibration38
- Calibration Report Printout38
12 Setting Printouts for Glp Procedures39
- Setting the Contents of Printouts for GLP Procedures40
13 Balance Operating Modes44
- Counting Details of the same Mass45
- Control Referring Mass of Set Standard49
- Control of % Deviation Referring Mass of Standard51
  - Mass of Standard Determined by Its Weighing52
  - Mass of Standard Entered to Balance Memory by User53
- Defining Thickness of Solids and Liquids54
  - Testing Thickness Solids55
  - Testing Thickness of Liquid55
- Pipettes Calibration55
14 F Unctions for Using Rs 23261
- Speed of Transmission61
- Continuous Transmission62
  - Continuous Transmission off in Basic Interval62
  - Continuous Transmission off in Actual Interval63
- Setting Type of Operating for RS 232 Joint64
- Designation of Data Type Sent through RS 232 Joint (Only for Non-Verified Balances)65
- Designation of Minimum Mass for Operating of some Functions66
- Printout to Printer or Computer67
15 Cooperation with Printer or Computer68
- Schedules of Connecting Conductors69
- Printing Data with Date and Time70
- Cooperation with Statistic Printout Kafka SQS70
- Format of Sending Data70
  - Format of Sent Data after Pressing the PRINT Button71
  - Format of Sent Data for Orders Generated from the Computer71
16 Weighing Loads under Balance72
17 List of Orders in Radwag Balances72
18 Error Messages73
19 Additional Equipment74
- Vibration Damping Table74
- Rack for Weighing Load under Balance74
- Set for Defining Thickness of Solids and Liquids74
- Additional Display74
- Computer Software74

Other manuals for RADWAG AS series

User Manual92 pages

Related product manuals

Preview: RADWAG AS R2

RADWAG AS 220.R

RADWAG AS 310.R2

Preview: RADWAG AS X2 Series

RADWAG AS X2 Series

RADWAG AS 60/220.R2

Preview: RADWAG AS PLUS Series

RADWAG AS PLUS Series

RADWAG AS 220.R2.PLUS

Preview: RADWAG WLC A1

Preview: RADWAG WLC/A1/C/2

RADWAG WLC/A1/C/2

RADWAG WLC/A2/C/2

Preview: RADWAG AS R2 PLUS

RADWAG AS R2 PLUS