Home
RADWAG
Scales
PS Series
RADWAG PS Series Operating Instructions
5
of 1
of 1 rating
74 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
52
RIGHT A
RROW
– choice of set digit;
TOP/DOWN A
RROW
- choice of value of
digit;
ENTER/PRINT
– confirmation of entered values
ATTENTION:
If user by mistake enters value of lowe
r threshold higher
than upper,
balance will
indicate error mess
age and will return to w
eighing.
Return to weighing
(see - 7.1.2. – return to weighing).
51
53
Table of Contents
Default Chapter
3
Table of Contents
3
1 Technical Data
6
2 Basic Information
8
Intended Use
8
Inappropriate Use
8
Warranty
8
Monitoring the Metrological Parameters of the Instrument
9
Data Included in this User Manual
9
Staff Training
9
3 Transport and Storage
9
Acceptance Check
9
Packaging
9
4 Unpacking, Installation and Commissoning
10
Installation and Operation Place
10
Unpacking
11
Positioning
12
Standard Accessories
12
Cleaning
12
Connection to Mains
12
Connection of Additional Equipment
12
5 Basic Functions of the Instrument
13
6 Keyboard
14
7 User Menu
15
Moving in User Menu
17
Return to Weighing Function
17
8 Weighing
17
Choice of Basic Weighing Unit
18
Choice of Weighing Unit (Temporary)
19
Setting Accessibility of Balance Operating Modes
20
Choice of Modes Quantity Accessible for User
20
Setting Contents of P6.1 Ffun - ALL Parameters
22
9 Main Setting Parameters
23
Setting Level of Filtering
24
Result Confirmation
25
Autozero Function
26
Light off the Last Display Digit
27
10 Another Parameters
28
Backlight of Weighing Result
28
Adjusting Brightness of Display Backlight
29
Beep" Signal - Reaction on Pressing Key
30
Printout of All Balance Parameters through RS 232 Port
31
11 Balance Calibration
31
Balance with Internal Calibration
32
Entering Calibration Menu
33
Calibration Test
37
Balances with Internal Calibration
37
Balances with External Calibration
38
Manual Calibration
39
Internal Calibration
39
External Calibration
40
Calibration Report Printout
40
12 Setting Printouts for Glp Procedures
41
Setting the Contents of Printouts for GLP Procedures
42
13 Balance Operating Modes
46
Counting Details of the same Mass
47
Control Referring Mass of Set Standard
50
Control of % Deviation Referring Mass of Standard
53
Mass of Standard Determined by Its Weighing
53
Mass of Standard Entered to Balance Memory by User
54
Defining Thickness of Solids and Liquids
55
Testing Thickness Solids
56
Testing Thickness of Liquid
56
Summing Function
57
14 Functions for Using Rs 232
59
Speed of Transmission
60
Continuous Transmission
61
Continuous Transmission off in Basic Interval
61
Continuous Transmission of in Actual Units
62
Setting Type of Operating for RS 232 Joint
63
Designation of Data Type Sent through RS 232 Joint
64
Designation of Minimum Mass for Operating of some Functions
65
15 Cooperation with Printer or Computer
66
Schedules of Connecting Conductors
67
Printing Data with Date and Time
68
Cooperation with Statistic Printout Kafka SQS
68
Format of Sending Data
68
Format of Sent Data after Pressing the PRINT Button
69
Format of Sent Data for Orders Generated from the Computer
69
16 Weighing Loads under Balance
70
17 List of Orders in Radwag Balances
71
Other manuals for RADWAG PS Series
User Manual
90 pages
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the RADWAG PS Series and is the answer not in the manual?
Ask a question
RADWAG PS Series Specifications
General
Brand
RADWAG
Model
PS Series
Category
Scales
Language
English
Related product manuals
RADWAG PS 600.R2
165 pages
RADWAG PS 360.R2
100 pages
RADWAG PS 1200.R2
165 pages
RADWAG PS 2100.R2
165 pages
RADWAG PS 4500.R2
165 pages
RADWAG PS 6000.R2
165 pages
RADWAG PS 6100 R2
95 pages
RADWAG PS/X series
86 pages
RADWAG AS R2
96 pages
RADWAG WLC/A2
54 pages
RADWAG AS 220.R
165 pages
RADWAG AS PLUS Series
100 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General