R&S ESU Series - Page 766

Operating Manual 1302.6163.12 - 03 6.327
R&S ESU Remote Control – Description of Commands
Differences in GPIB Behavior between the FSP and the FSE Families of Instruments
R&S
ESU
FSE [SENSe<1|2>:]POWer:ACHannel:REFerence:
AUTO
ONCE
R&S
ESU
FSE [SENSe<1|2>:]POWer:ACHannel:SPACing[:
ACHannel]
100Hz to 2000MHz different parameter
range
R&S
ESU
[SENSe<1|2>:]POWer:CHannel:SPACing:
CHANnel
100Hz to 2000MHz new function for
R&S ESU
FSE [SENSe<1|2>:]POWer:ACHannel:SPACing[:
UPPer]
0 to 1000MHz not available for
R&S ESU and FSET
R&S
ESU
FSE [SENSe<1|2>:]POWer:ACHannel:SPACing:
ALTernate<1|2>
100Hz to 2000MHz different parameter
range
R&S
ESU
[SENSe<1|2>:]POWer:ACHannel:TXCHannel:
COUNt
1 | 2 | 3 | 4 new function for
R&S ESU
R&S
ESU
[SENSe<1|2>:]POWer:ACHannel:REFerence:
TXCHannel:AUTO
MINimum | MAXimum |
LHIGhest
new function for
R&S ESU
R&S
ESU
[SENSe<1|2>:]POWer:ACHannel:REFerence:
TXCHannel:MANual
1 to 12 new function for
R&S ESU
R&S
ESU
FSE [SENSe<1|2>:]POWer:BANDwidth|BWIDth 10 to 99.9PCT different parameter
range
R&S
ESU
[SENSe<1|2>:]POWer:HSPeed ON | OFF new function for
R&S ESU
R&S
ESU
[SENSe<1|2>:]POWer:NCORrection ON | OFF new function for
R&S ESU
R&S
ESU
[SENSe<1|2>:]POWer:TRACe 1 to 3 new function for
R&S ESU
R&S
ESU
FSE [SENSe<1|2>:]ROSCillator:[INTernal:]TUNe 0 to 4095
R&S
ESU
FSE [SENSe<1|2>:]ROSCillator:[INTernal:]TUNe:SAVe
FSE [SENSe<1|2>:]ROSCillator:EXTernal:FREQuency 1MHz to 16MHz not available for
R&S ESU
R&S
ESU
FSE [SENSe<1|2>:]ROSCillator:SOURce INTernal | EXTernal
FSET/
ESIB
[SENSe<1|2>:]SCAN<:RANGes[COUNt] 1 to 10 not available for
R&S ESU
FSE/
ESIB
[SENSe<1|2>:]SCAN<1...10>:BANDwidth:
RESolution
f
min
to f
max
not available for
R&S ESU
FSET/
ESIB
[SENSe<1|2>:]SCAN<1...10>:INPut:ATTenuation dB
min
to dB
max
not available for
R&S ESU
FSET/
ESIB
[SENSe<1|2>:]SCAN<1...10>:INPut:ATTenuation:
AUTO
ON | OFF not available for
R&S ESU
FSET [SENSe<1|2>:]SCAN<1...10>:INPut:BIMPedance 150OHM | 600OHM |
10kOHM
not available for
R&S ESU
FSET [SENSe<1|2>:]SCAN<1...10>:INPut:GAIN 0dB to 30dB not available for
R&S ESU
FSET/
ESIB
[SENSe<1|2>:]SCAN<1...10>:INPut:GAIN:AUTO ON | OFF not available for
R&S ESU
Devices Command (Sheet 39 of 47) Parameter Notes