R&S ESU Series - Page 767

R&S ESU Remote Control – Description of Commands
Differences in GPIB Behavior between the FSP and the FSE Families of Instruments
6.328 Operating Manual 1302.6163.12 - 03
ESIB [SENSe<1|2>:]SCAN<1...10>:INPut:GAIN[:
STATE]
ON | OFF not available for
R&S ESU
ESIB [SENSe<1|2>:]SCAN<1...10>:INPut:TYPE INPUT1 | INPUT2 not available for
R&S ESU
FSET [SENSe<1|2>:]SCAN<1...10>:INPut:TYPE RF | BALanced not available for
R&S ESU
FSET/
ESIB
[SENSe<1|2>:]SCAN<1...10>:STARt f
min
to f
max
not available for
R&S ESU
FSET/
ESIB
[SENSe<1|2>:]SCAN<1...10>:STEP f
min
to f
max
not available for
R&S ESU
FSET/
ESIB
[SENSe<1|2>:]SCAN<1...10>:STOP f
min
to f
max
not available for
R&S ESU
FSET/
ESIB
[SENSe<1|2>:]SCAN<1...10>:TIME 100 µs to 100 s not available for
R&S ESU
R&S
ESU
FSE [SENSe<1|2>:]SWEep:COUNt 0 to 32767
R&S
ESU
FSE [SENSe<1|2>:]SWEep:EGATe ON | OFF
R&S
ESU
FSE [SENSe<1|2>:]SWEep:EGATe:HOLDoff 0 to 100s
R&S
ESU
FSE [SENSe<1|2>:]SWEep:EGATe:LENGth 0 to 100s
FSE [SENSe<1|2>:]SWEep:EGATe:LENGth 0 to 100s
FSE [SENSe<1|2>:]SWEep:EGATe:LEVel -5V to +5V not availabe for
R&S ESU
R&S
ESU
FSE [SENSe<1|2>:]SWEep:EGATe:POLarity POSitive | NEGative
R&S
ESU
FSE [SENSe<1|2>:]SWEep:EGATe:SOURce EXTernal | IFPower |
RFPower
R&S
ESU
FSE [SENSe<1|2>:]SWEep:EGATe:TYPE LEVel | EDGE
FSE [SENSe<1|2>:]SWEep:GAP ON | OFF not available for
R&S ESU
FSE [SENSe<1|2>:]SWEep:GAP:LENGth 0 to 100s not available for
R&S ESU
FSE [SENSe<1|2>:]SWEep:GAP:PRETrigger 0 to 100s not available for
R&S ESU
FSE [SENSe<1|2>:]SWEep:GAP:TRGTogap 0 to 100s not available for
R&S ESU
R&S
ESU
[SENSe<1|2>:]SWEep:POINts <numeric_value> not available for FSE
FSET/
ESIB
[SENSe<1|2>:]SWEep:SPACing LINear | LOGarithmic |
AUTO
not available for
R&S ESU
FSE/
FSIQ
[SENSe<1|2>:]SWEep:SPACing LINear | LOGarithmic not available for
R&S ESU
Devices Command (Sheet 40 of 47) Parameter Notes