Why is the radar target bearing incorrect on my Raymarine GPS?
If the bearing of a target on the Raymarine radar screen is incorrect, the radar bearing alignment needs adjustment. Check and correct the radar bearing alignment to resolve this issue.
What to do if Raymarine G-Series keyboard LCD shows low battery?
If the Raymarine keyboard LCD shows a low battery warning, charge the keyboard battery at the appropriate charge point. If the problem persists, the battery may be old and require replacement.
Why does my Raymarine G-Series monitor say 'Searching' or 'No signal'?
If your Raymarine monitor displays a “Searching” or “No signal” message, and your monitor is a repeater, allow a few minutes for the system to start up and see if the problem resolves itself. If not, ensure the monitor is set to the correct input channel. If using a glass bridge monitor, verify the cable from the GPM400 is connected to DVI1 on the rear of the monitor. Also, check the cable/connection between the monitor and the GPM400 processor or the appropriate signal source.
Why is my Raymarine G-Series GPS keyboard LCD blank?
If the Raymarine keyboard LCD is blank, check the keyboard wiring and power to the SeaTalkng bus. If it's a wireless keyboard, connect it to the charge point to ensure it has sufficient power.
Why is my Raymarine G-Series GPS monitor blank?
If your Raymarine monitor is blank, first ensure it is switched on and not in standby mode. If the screen remains blank, check the fuses, breakers, and power connections to the battery or originating power supply to ensure the monitor is receiving power.
How to troubleshoot Raymarine GPS system that won't start?
If your Raymarine system or a component isn't starting, the issue might stem from the power supply. Begin by inspecting the relevant fuses and breakers. Ensure the power supply cable is in good condition and that all connections are secure and free of any corrosion. Lastly, confirm that the power source matches the correct voltage and provides sufficient current.
General| Chartplotter | Yes |
|---|---|
| NMEA 2000 Compatible | Yes |
| Waterproof Rating | IPX6 |
| Radar Integration | Yes |
| Sonar Integration | Yes |
| Networking | NMEA 2000 |
| Video Input | Yes |
| Cartography | Navionics |
Crucial safety advice for installation and operation to prevent injury and damage.
Guidelines for handling chart cards, cleaning the display, and using sun covers.
Information on compatible chart cards, proper usage, and Electromagnetic Compatibility (EMC) installation.
Details on IMO/SOLAS regulations, technical accuracy disclaimers, and warranty registration.
Overview of available G-Series handbooks and the installation checklist for system setup.
Understanding Nav Station configurations and the overall system architecture with diagrams.
Connecting external devices and understanding networking constraints and protocols.
Best practices for cable routing, strain relief, isolation, and proper grounding.
Guidance on typical power distribution, circuit protection, fuses, and breakers.
Details on connecting via SeaTalkhs, SeaTalkng, and NMEA protocols.
Requirements for processor unit placement, ventilation, and avoiding ignition sources.
Instructions for mounting G-Series monitors and keyboards.
Installation and location requirements for the wireless base station and charging point.
Essential checks to ensure correct installation before system power-up.
Procedures for initial power-up, sequence, and verifying component operation.
Understanding keyboard controls and the first-time setup process.
Steps for setting up Nav Stations and assigning monitors and keyboards.
Configuration for language, compass, and GPS setup.
Verifying the correct operation of GPS, Radar, Sonar, and other integrated systems.
Procedures for setting up and checking thermal camera, video sources, and data flow.
Troubleshooting steps for common problems with power, monitors, and keyboards.
Diagnosing and resolving issues related to radar, GPS, and sonar systems.
Understanding LED indicators on SeaTalkhs switch, GPM processor, and GVM module.
Contact details and resources for obtaining technical assistance from Raymarine.
Information on support contacts for third-party components like Navionics.
Technical details for GPM processor and GVM400 video module.
Technical specifications for various G-Series keyboards and monitors.
Details on SeaTalk, SeaTalkng, and SeaTalkhs cables and network components.
Information on monitor, NMEA, audio/video cables, and available spare parts.
To Next Page
