To Next Page

To Previous Page

Chapter 2 Installation and Confirmation

b. External cooling

Outlet

Fan

Intlet Intlet

Guide

RM5G/P

Drive

RM5G/P

Drive

Outlet

Fan

Intlet Intlet

RM5G/P

Drive

RM5G/P

Drive

Correct Incorrect

Inlet InletInlet Inlet

Outlet

Intlet Intlet

RM5G/P

Drive

Fan

Outlet

Intlet Intlet

RM5G/P

Drive

Fan

Outlet

Correct Correct

Drive Drive

Inlet Inlet Inlet Inlet

Figure 2: Drive mounting inside the cabinet/control panel

Note: The external cooling is suitable for 2007,4010 above. Please ensure all air

vents to be ventilated using the external cooling.

Table of Contents8
Chapter 1 Cautions before Installation11
Product Verification11
Confirmation of Appearance11
The Description of Nomenclature11
Confirmation of Accessories12
Standard Specifications12
Three-Phase 200V Series12
Three-Phase 400V Series14
Common Specifications16
The Features of Control and Operation16
Chapter 2 Installation and Confirmation19
Basic Equipment19
Installing the Drive19
Descriptions of Terminal and Wiring Diagram23
Wiring Diagram and Setting for Single-Pump and Multi-Pump Applications40
Single Pump Control40
Dual & Multi-Pump Control (E-Mode 、 F-Mode 、 M-Mode)41
Multi-Pump Use of ACE-S12 Signal Distributor Control44
Multi-Pump Control (S-Mode Application)45
Chapter 3 The Setting of Keypad46
Functions of Keypad (KP-605)46
The Operation of Keypad(KP-605) and Monitor Mode48
Chapter 4 Parameter List55
Chapter 5 Parameter Setting Description71
The Keypad Setup71
Preset Speed Setup78
Multi-Speed Accel./Decel. Time Setup80
V/F Pattern Setup82
Analog Input Command Setup84
Analog Output Setup87
Motor Protecti Primary Frequency on Setup89
Multi-Function Input Setup90
Multi-Function Output Setup94
Automatic Torque Compensation97
System Overload Detection Setup98
Stall Prevention Setup99
DC Braking Set up100
Operation Selection at Instantaneous Power Failure100
Speed Tracing101
Current Limitation101
Others Function102
Parameter Description of Pump104
Related Settings of Feedback Signal (Pressure Transmitter) and Pump (Default: Iin Analog Input Terminal)104
Feedback Signal (Pressure Transmitter)104
Manual Mode106
Sequential Operation and Parallel Control of Multi-Pump107
Sequential Control for Multi-Pump(Only Used for F-Mode 、 E-Mode)107
Constant Pressure Control Mode and on / off Mode112
Constant Pressure Control Mode112
ON / off Control Mode113
PID Control Functions114
Pump Protection117
Cavitation Phenomenon118
Dry Running118
Noise Prevention119
Water Pipe and System Protection - over Pressure120
Error Trip Disposals121
Overheating Disposals122
Flow Sensor123
Compensation for Pipe Friction Loss124
Sequential Operation Control125
Operation Sequential Control126
Chapter 7 Communication Description128
Communication Wiring128
Communication Setting128
Communication Protocol128
Message Format129
CRC Checksum Algorithm132
Processing Time of Communication Transmission133
Communication Troubleshooting134
Drive Registers and Command Code135
Programming Examples - Register and Command139
Chapter 8 Operation Procedures and Fault Protection142
Operation Procedures142
Fault Protection Display and Troubleshooting144
Appendix A Peripheral Equipment of Drive150
Appendix B Selection of AC Reactor(ACL)151
Appendix C Selection of EMC Filter156
Appendix D Zero-Phase Radio Frequency Filter Selection158
Appendix E Selection of Motor162
Appendix F Instruction of Drive Charging164
Appendix G Dynamic Brake Unit and Braking Resistor165
Appendix H Instruction of Remote Controller and External Display173
Appendix I Outline Dimension Drawing of Drives175
Attachment 1 Dimension of Keypad (KP-605)179
Attachment 2 Default Value List180
Attachment 3 Setting Memo188
Attachment 4 Fault Display192

Brand	Rhymebus
Model	RM6F5 series
Category	Controller
Language	English

Rhymebus RM6F5 series User Manual

Table of Contents

Questions and Answers:

Rhymebus RM6F5 series Specifications

Related product manuals