Ricoh S-P2 - User Manual

Questions and Answers

K
Kelly DuncanAug 17, 2025
What causes a main motor error on a Ricoh S-P2?
- S
  stewartlisaAug 18, 2025
  If your Ricoh Printer shows a main motor error, it could be due to a defective main motor or a mechanical overload on the drive mechanism. This error can occur if the machine doesn't detect a main motor lock signal within 700 ms after the main motor starts, or if it detects the lock signal within 500 ms but then doesn't detect it again within 200 ms, or if it doesn't detect the lock signal within 200 ms after the motor switches off.
M
Melinda PriceAug 20, 2025
What does zero cross signal error mean on a Ricoh Printer?
- K
  Kathryn HamiltonAug 20, 2025
  If your Ricoh Printer displays a zero cross signal error, it means that zero cross signals of wavelength 50-60 Hz were not detected within 5 seconds after the fusing relay switched on, or zero cross interrupts did not issue at the prescribed 3 second intervals. This can be caused by a defective power supply board or a problem with the mains power supply.
F
folsonAug 22, 2025
Why does my Ricoh S-P2 Printer show an electrical total counter error?
- S
  Summer MillerAug 22, 2025
  If your Ricoh Printer has an electrical total counter error, it indicates that the total counter contains non-numerical data. This can be caused by an incorrect NVRAM type, a defective NVRAM, scrambled NVRAM data, or an unexpected error from an external source.
C
Christine JeffersonAug 26, 2025
How to fix 'Printer error 1' on a Ricoh S-P2?
- R
  Ronald BlackAug 26, 2025
  If your Ricoh Printer shows a 'Printer error 1', it indicates an internal application error that prevents operation from continuing. This may be due to defective software. Try turning the machine off and on, or change the controller firmware or insufficient memory.
K
kimberlychandlerAug 28, 2025
Why does the fusing lamp remain on my Ricoh S-P2 Printer?
- B
  Brenda SinghAug 28, 2025
  If the fusing lamp remains on for longer than 12 seconds after the fusing unit reaches optimum temperature and the main motor switches off on your Ricoh Printer, this could be due to a defective fusing thermistor, a faulty power supply board, or a defective connection of the fusing unit.
B
Briana KennedyAug 30, 2025
What causes a development bias leak on a Ricoh Printer?
- C
  Colton WalkerAug 30, 2025
  If the Ricoh Printer detects a development bias leak signal for 200 ms, it indicates a development bias leak. This can be caused by a defective high voltage supply board or a defective cartridge connection.
J
Jim PerrySep 1, 2025
What does 2nd beam laser synchronization error mean for Ricoh S-P2?
- C
  Cassidy ThompsonSep 1, 2025
  If your Ricoh Printer experiences a 2nd beam laser synchronization error, with all doors closed, the polygon motor is locked and not rotating, or the laser synchronization detector could not detect 2nd beam laser detection signal within 500 ms. This can be caused by a laser synchronization detector board out of position, a defective LD unit, or a defective engine board.
S
Sandra ConnerSep 4, 2025
What to do if Ricoh S-P2 shows address book data error?
- C
  creynoldsSep 4, 2025
  If your Ricoh Printer shows an address book data error, it means that the address book data on the hard disk was detected as abnormal when accessed from either the operation panel or the network. This is often due to a defective HDD. Initialize the HDD with SP5832. If this does not solve the problem, replace the HDD and initialize with SP5832. Note: If you turn off the machine while the HDD is being accessed, this can damage the HDD.
R
reynoldsjacquelineSep 6, 2025
What causes HDD mail receive data error in Ricoh S-P2?
- G
  gabriel77Sep 7, 2025
  If the Ricoh Printer detects that the HDD was not operating correctly at power on, it results in an HDD mail receive data error. This is often due to a defective HDD. Initialize the HDD with SP5832. If this does not solve the problem, replace the HDD and initialize with SP5832. Note: If you turn off the machine while the HDD is being accessed, this can damage the HDD.
B
beverly05Sep 9, 2025
How to reset Fusing unit SCs on Ricoh S-P2?
- J
  Jacqueline HillSep 9, 2025
  To reset Fusing unit SCs shown on the operation panel on Ricoh Printer, do SP5810 and press [#Enter]. When "execute" is displayed, press [#Enter] again. Then, press [Escape] and turn the machine power off/on.