Name: Rigol MSO2000A Series
Brand: Rigol
Rating: 4 (1 reviews)

To Next Page

To Previous Page

RIGOL Chapter 5 To Trigger the Oscilloscope

5-46 MSO2000A/DS2000A User’s Guide

Trigger Setting:

Press Setting to set the trigger parameters (noise rejection) under this trigger type.

Note: Noise rejection is grayed out and disabled automatically when the signal

source is set to any channel of D0-D15.

Trigger Level:

Press SCL and use TRIGGER LEVEL to modify the trigger level of the SCL

channel. Press SDA and use TRIGGER LEVEL to modify the trigger level of the

SDA channel. For the details, please refer to the introduction of “

Trigger Level”.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Guaranty and Declaration3
Safety Requirement4
- General Safety Summary4
- Safety Terms and Symbols7
- Allgemeine Sicherheits Informationen8
- Sicherheits Begriffe und Symbole11
- Measurement Category12
- Ventilation Requirement13
- Working Environment14
- General Care and Cleaning16
- Environmental Considerations17
MSO2000A/DS2000A Series Overview18
Document Overview20
- Table of Contents23
Chapter 1 Quick Start31
- General Inspection32
- Appearance and Dimensions33
- To Prepare the Oscilloscope for Use34
- Front Panel Overview39
- Rear Panel Overview41
- Front Panel Function Overview43
- User Interface51
- To Use the Security Lock56
- To Use the Built-In Help System57
Chapter 2 To Set the Vertical System59
- To Enable the Analog Channel60
- Channel Coupling61
- Bandwidth Limit61
- Probe Ratio62
- Input Impedance63
- Waveform Invert63
- Vertical Scale64
- Vertical Expansion65
- Amplitude Unit65
- Channel Label65
- Delay Calibration of the Analog Channel67
Chapter 3 To Set the Horizontal System69
- Delayed Sweep70
- Time Base Mode72
- Horizontal Scale76
- Horizontal Reference77
Chapter 4 To Set the Sample System79
- Acquisition Mode80
- Sample Mode83
- Sample Rate84
- LA Sample Rate85
- Memory Depth86
- LA Memory Depth87
- Anti-Aliasing87
Chapter 5 To Trigger the Oscilloscope89
- Trigger Source90
- External Trigger Input90
- Trigger Mode91
- Trigger Coupling93
- Trigger Holdoff94
- Noise Rejection95
- Trigger Type96
- Trigger Output Connector141
Chapter 6 MATH and Measurements143
- Math Operation144
- Auto Measurement157
- Cursor Measurement171
Chapter 7 Digital Channel183
- To Select the Digital Channel184
- To Move the Digital Channel184
- To Turn On/Off the Digital Channel185
- Group Set186
- To Set the Waveform Display Size187
- Reorder Setting187
- To Set the Threshold187
- To Use the Digital Bus188
- To Set the Label189
- Digital Channel Delay Calibration190
Chapter 8 Protocol Decoding191
- Parallel Decoding192
- RS232 Decoding (Option)195
- I2C Decoding (Option)200
- SPI Decoding (Option)204
- CAN Decoding (Option)207
Chapter 9 Reference Waveform211
- To Enable REF Function212
- To Set the Color212
- To Select REF Source212
- To Save REF Waveform213
- To Adjust REF Waveform Display213
- To Export to Internal or External Memory213
- To Import from Internal or External Memory214
Chapter 10 Pass/Fail Test215
- To Enable Pass/Fail Test216
- To Select Source216
- Mask Range216
- To Set Test Results Output Type218
- To Save the Test Mask219
- To Load the Test Mask219
Chapter 11 Waveform Record221
- Waveform Record222
- Record Constant on224
- Waveform Playback226
- Waveform Analysis228
  - Analysis Based on Trace232
  - Analysis Based on Pass/Fail Mask233
Chapter 12 Display Control235
- To Select the Display Type236
- To Set the Persistence Time236
- To Set the Waveform Intensity238
- To Set the Screen Grid238
- To Set the Grid Brightness238
- To Set the Menu Display238
Chapter 13 Signal Source239
- Parameter Setting Method240
- To Output Basic Waveform241
- To Output Built-In Waveform246
- To Output Arbitrary Waveform250
- Modulation257
Chapter 14 Store and Recall261
- Storage System262
- Storage Type263
- Internal Storage and Recall265
- External Storage and Recall267
- Disk Management269
- Factory275
Chapter 15 System Function Setting283
- Remote Interface Configuration284
- System-Related290
Chapter 16 Remote Control303
- Remote Control Via USB304
- Remote Control Via LAN308
- Remote Control Via GPIB310
Chapter 17 Troubleshooting313
Chapter 18 Specifications317
- General Specifications328
- Calibration Interval328
Chapter 19 Appendix329
- Appendix A: Accessories and Options329
- Appendix B: Warranty331
Index333

Rigol MSO2000A Series User Manual

Table of Contents

Other manuals for Rigol MSO2000A Series

Questions and Answers:

Rigol MSO2000A Series Specifications

Related product manuals

Brand	Rigol
Model	MSO2000A Series
Category	Test Equipment
Language	English