Name: Rigol MSO2000A Series
Brand: Rigol
Rating: 4 (1 reviews)

To Next Page

To Previous Page

RIGOL Chapter 13 Signal Source

13-22 MSO2000A/DS2000A User’s Guide

1 Hz to 50 kHz.

5. Set the Modulation Deviation

Press Deviation to set the deviation of the frequency of the modulating

waveform relative to the carrier frequency. The range is from 0 Hz to the current

carrier frequency and the sum of the frequency deviation and carrier frequency

cannot be greater than the sum of the current carrier frequency upper limit and

1 kHz. For the setting method, please refer to the introduction in “

Parameter

Setting Method”.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Guaranty and Declaration3
Safety Requirement4
- General Safety Summary4
- Safety Terms and Symbols7
- Allgemeine Sicherheits Informationen8
- Sicherheits Begriffe und Symbole11
- Measurement Category12
- Ventilation Requirement13
- Working Environment14
- General Care and Cleaning16
- Environmental Considerations17
MSO2000A/DS2000A Series Overview18
Document Overview20
- Table of Contents23
Chapter 1 Quick Start31
- General Inspection32
- Appearance and Dimensions33
- To Prepare the Oscilloscope for Use34
- Front Panel Overview39
- Rear Panel Overview41
- Front Panel Function Overview43
- User Interface51
- To Use the Security Lock56
- To Use the Built-In Help System57
Chapter 2 To Set the Vertical System59
- To Enable the Analog Channel60
- Channel Coupling61
- Bandwidth Limit61
- Probe Ratio62
- Input Impedance63
- Waveform Invert63
- Vertical Scale64
- Vertical Expansion65
- Amplitude Unit65
- Channel Label65
- Delay Calibration of the Analog Channel67
Chapter 3 To Set the Horizontal System69
- Delayed Sweep70
- Time Base Mode72
- Horizontal Scale76
- Horizontal Reference77
Chapter 4 To Set the Sample System79
- Acquisition Mode80
- Sample Mode83
- Sample Rate84
- LA Sample Rate85
- Memory Depth86
- LA Memory Depth87
- Anti-Aliasing87
Chapter 5 To Trigger the Oscilloscope89
- Trigger Source90
- External Trigger Input90
- Trigger Mode91
- Trigger Coupling93
- Trigger Holdoff94
- Noise Rejection95
- Trigger Type96
- Trigger Output Connector141
Chapter 6 MATH and Measurements143
- Math Operation144
- Auto Measurement157
- Cursor Measurement171
Chapter 7 Digital Channel183
- To Select the Digital Channel184
- To Move the Digital Channel184
- To Turn On/Off the Digital Channel185
- Group Set186
- To Set the Waveform Display Size187
- Reorder Setting187
- To Set the Threshold187
- To Use the Digital Bus188
- To Set the Label189
- Digital Channel Delay Calibration190
Chapter 8 Protocol Decoding191
- Parallel Decoding192
- RS232 Decoding (Option)195
- I2C Decoding (Option)200
- SPI Decoding (Option)204
- CAN Decoding (Option)207
Chapter 9 Reference Waveform211
- To Enable REF Function212
- To Set the Color212
- To Select REF Source212
- To Save REF Waveform213
- To Adjust REF Waveform Display213
- To Export to Internal or External Memory213
- To Import from Internal or External Memory214
Chapter 10 Pass/Fail Test215
- To Enable Pass/Fail Test216
- To Select Source216
- Mask Range216
- To Set Test Results Output Type218
- To Save the Test Mask219
- To Load the Test Mask219
Chapter 11 Waveform Record221
- Waveform Record222
- Record Constant on224
- Waveform Playback226
- Waveform Analysis228
  - Analysis Based on Trace232
  - Analysis Based on Pass/Fail Mask233
Chapter 12 Display Control235
- To Select the Display Type236
- To Set the Persistence Time236
- To Set the Waveform Intensity238
- To Set the Screen Grid238
- To Set the Grid Brightness238
- To Set the Menu Display238
Chapter 13 Signal Source239
- Parameter Setting Method240
- To Output Basic Waveform241
- To Output Built-In Waveform246
- To Output Arbitrary Waveform250
- Modulation257
Chapter 14 Store and Recall261
- Storage System262
- Storage Type263
- Internal Storage and Recall265
- External Storage and Recall267
- Disk Management269
- Factory275
Chapter 15 System Function Setting283
- Remote Interface Configuration284
- System-Related290
Chapter 16 Remote Control303
- Remote Control Via USB304
- Remote Control Via LAN308
- Remote Control Via GPIB310
Chapter 17 Troubleshooting313
Chapter 18 Specifications317
- General Specifications328
- Calibration Interval328
Chapter 19 Appendix329
- Appendix A: Accessories and Options329
- Appendix B: Warranty331
Index333

Rigol MSO2000A Series User Manual

Table of Contents

Other manuals for Rigol MSO2000A Series

Questions and Answers:

Rigol MSO2000A Series Specifications

Related product manuals

Brand	Rigol
Model	MSO2000A Series
Category	Test Equipment
Language	English