59
Chapter 5. Parameter guide
Chapter 5
STEP
OFF, 0–100, BPM –
Adjusts the interval at which the Rate and Depth will change
in “stair-step” fashion. Larger settings will produce smaller
changes.
* If this is set to BPM, the value of each parameter will be set by
the tempo value (p. 23) specified for each patch. This makes it
easy to create effect sounds that are synchronized to the tempo
of your song.
BALANCE
D=100, E=0–D=0, E=100
Adjusts the balance of the direct sound and effect sound.
LEVEL
0–100
Adjusts the volume of the phaser.
● If the type is set to “SUB EQ”
HIGH G
(High gain) -20–+20 dB
Adjusts the tone of the upper range.
LOW G
(Low gain) -20–+20 dB
Adjusts the tone of the lower range.
L-MID G
(Low middle gain) -20–+20 dB
Adjusts the tone of the low-mid frequency range.
H-MID G
(High middle gain) -20–+20 dB
Adjusts the tone of the high-mid frequency range.
L-MID Q
(Low middle Q) 0.5–16
Adjusts the width of the region centered on the “L-MID F”
frequency that will be affected by the EQ. Higher settings
will make the region narrower.
L-MID F
(Low middle frequency)
100 Hz–10.0 kHz
Specifies the center frequency of the region adjusted by “L-
MID G.”
H-MID Q
(High middle Q) 0.5–16
Adjusts the width of the region centered on the “H-MID F”
frequency that will be affected by the EQ. Higher settings
will make the region narrower.
H-MID F
(High middle frequency) 20 Hz–10.0 kHz
Specifies the center frequency of the region adjusted by “H-
MID G.”
LEVEL
-20–+20 dB
Adjusts the volume of the sound that has passed through the
equalizer.
● If type if set to “2x2 CHORUS”
X OVER F
(Crossover frequency) 100 Hz–4.00 kHz
Specifies the frequency at which the direct sound will be split
into high-frequency and low-frequency components.
* Adjust both in lower (LOW) and upper (HIGH) range, for
each of the following parameters.
RATE
0–100, BPM –BPM
Adjusts the speed of the chorus effect.
* If this is set to BPM, the value of each parameter will be set by
the tempo value (p. 23) specified for each patch. This makes it
easy to create effect sounds that are synchronized to the tempo
of your song.
DEPTH
0–100
Adjusts the depth of the chorus effect. Set this to “0” if you
are using the effect as a doubling effect.
PRE DLY
(Pre delay) 0.0–40.0 msec (0.5 msec steps)
Adjusts the time from when the direct sound is output until
the effect sound is output. Lengthening the pre-delay will
produce the impression of multiple sound sources heard
simultaneously (the doubling effect).
LEVEL
0–100
Adjusts the volume.
● If the type is set to “TREMOLO” or
“PAN”
WAVE
0–100
For TREMOLO, this adjusts the smoothness of the volume
change.For PAN, this adjusts the smoothness of the pan change.
RATE
0–100, BPM –BPM
Adjusts the modulation speed of the effect.
* If this is set to BPM, the value of each parameter will be set by
the tempo value (p. 23) specified for each patch. This makes it
easy to create effect sounds that are synchronized to the tempo
of your song.
DEPTH
0–100
Adjusts the depth of the effect.
To Next Page
Loading...
