SA Instruments 1030 - Chapter 2 System Setup

194 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Chapter 2

System Setup

Table of Contents

Default Chapter3
- Table of Contents3
Introduction9
Chapter 1 System Overview11
- Monitoring and Gating13
- System Components13
Chapter 2 System Setup17
- Installation of Software19
- Setting up the Hardware19
- Communication Port Assignment21
- Setting the Communication Port in PC-Sam21
- Testing the Monitoring and Gating System21
- Testing the Heater System22
- Step by Step Instructions for Monitoring and Gating23
- Recommendations for Daily Operation24
Chapter 3 PC and ERT Control/Gating Module25
- Overview27
- Monitor Display27
- Labeling Convention for Respiration Channels30
- User Input Channels30
- ERT Control/Gating Module Input/Output Connections31
- Gate Output Pulse Signal Configuration31
- Altering Monitor Configuration31
- Snapshot Key33
- Trend Key33
- GATING SETUP Window34
- R-DETECT Setup Window35
- CHARGER Window37
Chapter 4 ERT Module39
- Overview41
- Positioning the ERT Module41
- Attaching ECG Electrodes42
- Connecting the Battery Pack Cable42
- Positioning ECG Lead Wires42
- Attaching the Temperature Probe46
- Positioning the Thermister Temperature Probe47
- Charging the ERT Battery Pack47
- ERT Battery Pack Protection Circuit48
- Setting the 50/60 Hz Notch Filter48
Chapter 5 Simulator49
- Overview51
- Operation52
- Battery Replacement53
- Capnograph and Ventilator Option54
Chapter 6 Air Heater System55
- Overview57
- Heater Components57
- Heater Control59
- Heating the Mouse60
Chapter 7 Trends61
- Overview63
- Trendmap Viewer Display63
- Source Trend Key65
- Get and Save Setup Keys65
- TREND ORDER ADJUSTMENT Window65
- Mark Stop and Mark Stop Keys66
- Define Output Key66
- Selecting Events Recorded in Trend Data67
- Trend Data Item List68
Chapter 8 Snapview71
- Overview73
- Snapview Display73
- SETUP Window74
- Rerun Key75
- Print Key75
- Export Key75
Chapter 9 Additional Features77
- SYSTEM INFORMATION Window79
- SET COLORS Window80
- ALARMS Window81
- Cardiac and Respiratory Sweep Gates82
- Freeze/Thaw Key83
- Event Key83
Chapter 10 Invasive Blood Pressure85
- Overview87
- Fiber Optic Communication Cable Connections87
- IBP Transducers87
- Animal Cannula89
- Flushing the IBP Transducer and Cannula91
- Making Blood Pressure Measurements91
- Zeroing the Invasive Blood Pressure Transducer92
- Calibrating the Invasive Pressure Transducer92
- Charging the IBP Module Internal Battery92
- Spare Channels for Auxiliary Data93
Chapter 11: Pulse Oximetry Module95
- Overview97
- Oximeter Components and Connection97
- Display Configuration98
- Changing Sensor Clips and Forms98
- Attachment of Fiber Optic Oximetry Sensors100
- PC-Sam's Main Display101
- Plethysmogram Gate Threshold102
Chapter 12 Fiber Optic Temperature105
- Overview107
- Components and Connections107
- Display Configuration108
- Attaching, Handling and Cleaning Fiber Optic Temperature Probes108
- PC-Sam's Main Display109
- Heater Control109
Chapter 13 Fiber Optic Pressure111
- Overview113
- Fiber Optic Communication Cable Connections114
- Display Configuration116
- Calibrating Fiber Optic Pressure Sensor116
- Zeroing the Fiber Optic Pressure Sensor117
- Inserting the Fiber Optic Pressure Sensor118
- PC-Sam's Main Display118
- Procedure for Making IBP Measurements from the Rat Tail Artery119
Chapter 14 Capnograph and Ventilator121
- Overview123
- Ventilator MR-Compatible Valve Assembly123
- Ventilator Setup in MR124
- Ventilator Operation125
- Microcapstar Capnograph125
- Capnograph Setup in MR125
- Capnograph Operation126
- Capnograph/Ventilator Interface Module126
- Display Configuration126
- PC-Sam Main Display127
Chapter 15 Advanced Features129
- Inversion Timing133
- USER RESP SETUP Window133
- USER IBP SETUP Window134
- AUTO EVENT for Time Stamping135
- ADVANCED GATING SETUP Window136
- Auto Track136
Chapter 16 Signal Breakout Module139
- Overview141
- Input/Output Connections141
- Setup and Use142
- Using Multiple Signal Breakout Modules143
- Signal Breakout Module Data Formats144
- Capturing ASCII Slow Data from the Serial Output144
- Capturing ASCII Waveform Data from the Serial Output144
- Capturing Digital Waveform Data from the Serial Output145
Chapter 17 Fiber Optic Universal Gating Module147
- Overview149
- Controls and Connections149
- Setup and Use150
Chapter 18 Micro-Imaging MR Systems151
- Overview153
- Micro-Imaging Kit153
- Micro-Imaging Equipment Setup154
- Bruker Micro 2.5 Mouse and Micro 2.5 AHS/RF Imaging Probes155
- Bruker Mini 0.5 AHS/RF Imaging Probe156
- Bruker Micro-Imaging Kit Components157
Chapter 19 Water Bed Heater System159
- Overview161
- Operation in the Standalone Mode161
- Operation with a SAII Monitoring and Gating System161
- WBH USER INTERFACE Window162
- TEST and SERVICE Window163
- Circulation Module Input Output Connections164
- Heater Module Input Output Connections165
- Water Beds166
- Water Bed Heater System Setup in MR166
- Turning on the Water Bed Heater Control169
- Changing the Water Bed169
- Polyether as an Alternate Fluid169
Appendix A: Appendix C Troubleshooting179
- ERT Communication Error182
- Check Communication between the PC and ERT Control/Gating Module182
- No Heat from the Heater183
- Low Heat from the Heater183
- Gating Setup When Large Artifacts Are Present in the ECG Waveform184
Appendix D Routine Maintenance187
Appendix E Example Waveforms189
Appendix F193
Warranty, Service and Support193