Sanyo PLC-XP100L - Page 58

-58-
Electrical Adjustment
Grp Item Item Name Function Range Initial
11 Alpha Contrast
120/120/120/120/120/
120/120/120/120/120/120
12 Alpha Brightness
120/120/120/120/120/
120/120/120/120/120/120
13 Alpha Color
120/120/120/120/120/
120/120/120/120/120/120
14 Alpha Tint
10/10/10/10/10/
10/10/10/10/10/10
15 Alpha WhiteBalance-Red 0-500
40/40/40/40/40/
40/40/40/40/40/40
16 Alpha WhiteBalance-Green 0-500
40/40/40/40/40/
40/40/40/40/40/40
17 Alpha WhiteBalance-Blue 0-500
40/40/40/40/40/
40/40/40/40/40/40
18 Alpha BlackBalance-Red 0-500
20/20 /20/20 /20/
20/20 /20/20 /20/20
19 Alpha BlackBalance-Green 0-500
20/20 /20/20 /20/
20/20 /20/20 /20/20
20 Alpha BlackBalance-Blue 0-500
20/20 /20/20 /20/
20/20 /20/20 /20/20
680 Auto Caribaration
0 Execute Calibration
Auto-calibration will execute when the value changes
(For PC White-100% Adjustment)
0 - 1 0
1 Loop Count Maximum times of Calibration 1 - 30 3
2 OFFSET AREA H START H Start Position at Black level acquire area 0 - 1000 975
3 OFFSET AREA V START V Start Position at Black level acquire area 0 - 1000 500
4 GAIN AREA H START H Start Position at White level acquire area 0 - 1000 25
5 GAIN AREA V START V Start Position at White level acquire area 0 - 1000 500
6 Image AREA H WIDTH Black/White level acquire area width 0 - 4095 13
7 Image AREA V HIGHT Black/White level acquire area height 0 - 4095 9
8 OFFSET target Black level adj. target 0 - 127 1
9 OFFSET torelance Black level adj. trelance 1 - 127 1
10 GAIN target White level adj. target 0 - 255 235
11 GAIN tolerance White level adj. tolerance 1 - 255 1
12 Auto Status
Auto Calibration Result * Read only
0: End correctly / 1: on adjustment / 9: End at Error
0 / 1 / 9 0
13 Auto Wait Wait value 1 - 20 1
14 CHECK -Tolelance Offset Final check Tolerance 1 - 255 1
681 AutoPC Adjust
0 AutoPCAdjustEnable 0:AutoPCAdjust Enable 1:AutoPCAdjust Prohibit 0 - 1 0
1 Frequency Step TotalDot Search Steps 0-3 1
2 Frequency Threshold
TotalDot Match
0 [] <--- -----> 10[Not Match]
0 - 10 5
3 Fine Phase
Fine Phase after Total Dot Adj.
0: FinePhase Enable / 0 : FinePhaseDiable
0 - 1 0
4 BLKDET Black Level Detect Area 0 - 3 1
5 PHASEMSK
Phase Detect Filter 0: All bit １:Lower 1 bit Disable
2: Lower 2 bit Disable 3: Lower 3 bit Disable
0 - 3 0
685 Auto Calibration - YCbCr <10bit>
0 Gain Area H Start - Y Acquire Area of Y Signal H-Start Position 0 - 1000 25
1 Gain Area V Start - Y Acquire Area of Y Signal V-Start Position 0 - 1000 200
6 Image Area H Width Acquire Area of Signal Width 0 - 4095 13
7 Image Area V Height Acquire Area of Signal Height 0 - 4095 9
8 Gain Target - Y Target Value of Y Signal 0 - 1023 790
11 Gain Tolerance Gain Tolerance 0 - 1023 1
12 Output Tolerance Output Tolerance 0 - 1023 5
686 Auto Calibration - CVBS <10bit>
0 Gain Area H Start - Y Acquire Area of Y Signal H-Start Position 0 - 1000 25
1 Gain Area V Start - Y Acquire Area of Y Signal V-Start Position 0 - 1000 200
6 Image Area H Width Acquire Area of Signal Width 0 - 4095 13
7 Image Area V Height Acquire Area of Signal Height 0 - 4095 9
8 Gain Target - Y Target Value of Y Signal 0 - 1023 790
11 Gain Tolerance Gain Tolerance 0 - 1023 1
12 Output Tolerance Output Tolerance 0 - 1023 5
690 CUSTOM(Aspect)
0 Connect Indivisual/Interlock Selection 0:Indivusual/1:Interlock 0 - 1 0
1 Horizontal Scaler H-Scaler 0 - 200 100
2 Horizontal Position H-Position Correct 0 - 200 100