www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
23 I 72
m WARNING
Vapours of fuels and solvents may explode.
Rex the security and safety equipment after repara-
tion and maintenance work.
Keep the machine in safe work condition. Especially
check the fuel system for tightness.
Always remove any dirt from the cooling ns of the
engine.
Residual risks and accident prevention
standards
Neglect of ergonomic principles
Negligent handling of personal protective equip-
ment
Negligent handling or ommission of the personal pro-
tective equipment may cause serious injuries.
– Wear prescribed personal protection equipment.
Human behaviour, misbehaviour
For any work be fully concentrated.
m Residual risks - Cannot be entirely excluded.
Electrical residual risks
Electrical contact
Touching the spark plug may cause an electrical
shock.
– Never touch the spark plug while the engine is
running.
Thermal residual risks
burns, chilblains
Touching of the exhaust/ case may cause burns.
– allow motor driven machines to cool.
Danger from noise
hearing damage
Prelonged unprotected work with the device may
cause hearing damage.
– Always wear ear-muffs
Danger caused by materials and other substanc-
es
Contact, inhalation
The emissions of the machine may cause damages
to health.
– Only use the motor driven machine outdoors.
Fire, explosion
m Fuel is ammable.
– During work and refuelling smoking and open
ames are prohibited.
In case of emergency
In case of a possibly occuring accident take the nec-
essary rst aid steps as appropriate and obtain quali-
ed medical aid as quickly as possible.
11. Do not overload the machine capacity. Drive at
a safe speed, adjusting the speed to the slope
of the land, the surface conditions of the road,
and the weight of the load.
12. Use extreme caution when in reverse or pulling
the machine towards you.
13. Exercise extreme caution when operating on
or crossing gravel drives, walks, or roads. Stay
alert for hidden hazards or trafc.
14. On soft ground, drive at the rst forward/reverse
gear. Do not rapidly accelerate, turn sharply or
stop.
Safety informations service/ mainte-
nance and storage
1. Only original parts may be used for maintenance
and accessories.
2. Replace faulty silencers.
3. Before using, always visually inspect to see that
the tools are not worn or damaged. Replace
worn or damaged elements and bolts. Keep all
nuts, bolts and screws tight to be sure the equip-
ment is in safe working condition.
4. Regularly check for leakage or traces of abrasion
in the fuel system, such as porous pipes, loose or
missing clamps and damage to the tank or tank
cap. Before use all defects must be repaired.
5. Before checking or adjusting the machine or the
motor, the ignition plug and the ignition wire re-
spectively must be removed to prevent acciden-
tal starting.
Storage
1. Never store the equipment with petrol in the tank
inside a building where fumes can reach an open
ame or spark.
2. Allow the engine to cool before storing in any en-
closure.
3. To reduce the re hazard, keep the engine, si-
lencer, battery compartment and petrol storage
area free of vegetative material and excessive
grease.
Long term storage/hibernation
1. In case of long term storage drain out the com-
plet fuel. Fuels are chemical compounds which
change their properties during prolonged stor-
age. If the fuel tank has to be drained out this
should happen outdoors.
m WARNING
Improper maintenance or ignoring/ not rectifying a
problem during the operation may become a source
of danger. Operate your machine only if regular-
ly maintained. Only in this way you can assume that
your device is operating safe, economical and with-
out malfunctions.
Do not clean, maintain, setup or repair the ma-
chine whilst running. Moving parts may cause
serious injuries.
Do not use fuel or other ammable solvents to clean
the equipment.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
