SCHIEBEL ACTUSAFE CMFS - Direction of Rotation Handwheel for Closing the Valve, Failsafe Move out

99 pages

Save Page as PDF

To Next Page

To Previous Page

7 Commissioning

Operating Manual Linear ACTUSAFE CMFS(L)

OM-ENGLISH-Failsafe-Linear-16xx-V2.00-2022.03.03

7.2.3 Direction of rotation handwheel for closing the valve, Failsafe „move out“

Figure 5: Roation of direction for Failsafe direction „move out“.

Main Page

Table of Contents2
Contents4
Manual for Linear Failsafe-Actuators - CMFS(L)5
Safety Instructions5
Introduction6
Functional Description of the CM FS(L) Failsafe Drive7
Failsafe-Direction8
Moving-Behaviour of the Actuator8
Moving Behaviour Electrical Mode8
Moving Behaviour Failesafe Mode8
General Information8
Serial Number8
Protection Class8
Mounting Position8
Direction of Rotation8
Protective Devices9
Ambient Temperature9
Condition on Delivery of the Actuators9
Note (Tag)9
Transport and Storage9
Installation Instructions9
Mechanical Connection; Preparations9
Mounting of Linear Failsafe Actuator10
Mounting Procedure for Valve Without Required Sealing Force11
Alternative Procedure for Valve with Required Sealing Force11
Mounting Position of the Control Unit11
Electrical Connection11
Commissioning12
General Information12
Manual Operation12
Activate Manual Operation13
Deactivate Manual Operation13
Direction of Rotation Handwheel for Closing the Valve, Failsafe „Move out14
Direction of Rotation Handwheel for Closing the Valve, Failsafe „Move in15
Required Force on the Handwheel16
Mechanical Default Setting, Preparation16
Setting the End Positions16
Adjusting of Failsafe Speed16
Setting Procedure17
Final Work18
The Control Unit18
Maintenance19
Technical Data Failsafe Brake20
Cm03Fs(L)20
Cm06Fs(L)20
Cm12Fs(L)20
Spare Parts20
Lubricant Recommendation / Lubricant Requirements20
Lubricant Points FS(L)20
Basic Lubricant Service Interval21
Training21
Mode of Operation FS(L)22
Cm03Fs(L)22
Cm06Fs(L)23
Operating Manual ACTUSMART CM.V1.224
Introduction/Notes24
General25
Overview25
Serial Number and Type Label25
Operating Mode26
Protection Class26
Mounting Position26
Direction of Rotation26
Protection Devices27
Torque27
Motor Temperature27
Input Fuse, Thermal Fuse27
Ambient Temperature27
Delivery Condition of the Actuators27
Information Notice (Tag)27
Packaging, Transport and Storage28
General28
Storage28
Long-Term Storage28
Installation Instructions29
Mechanical Connection29
Mounting Postion of the Operating Unit30
Electrical Connection31
Power Supply Connection31
Commisioning32
General32
Manual Operation32
Mechanical Default Settings, Preparation32
User Level and Permissions33
End Limit Setting33
End Limit OPEN33
End Limit CLOSE35
Final Works36
Control Unit36
Operating Unit36
Display Elements37
Graphic Display37
LED Display37
Operation38
Welcome Menu38
Operation Mode40
Configuration40
Configuration Example41
Teachin42
Parameter Menu44
Parameter Group: End Limit44
Parameter Group: Torque45
Parameter Group: Speed46
Parameter Group: Ramp (Optional)46
Parameter Group: Control46
Parameter Group: User Level47
Parameter Group: Position49
Parameter Group: Binary Inputs50
Parameter Group: Binary Outputs53
Parameter Group: Position Output (Optional)57
Parameter Group: Step Mode57
Parameter Group: Positioner (Optional)59
Parameter Group: PID Controller (Optional)61
Parameter Group: Bus Systems (Optional)62
Parameter Group: Characteristic Curves (Optional)63
Torque Characteristic63
Speed Characteristic64
Valve Characteristic64
Parameter Group: Identification (Optional)65
Parameter Group: System Parameters65
Parameter Group: Miscellaneous66
Default User Level Settings68
Status Area71
Status71
Status - Binary Outputs71
Status - Binary Inputs71
Status - Analog Values72
Status - Absolute Values72
Status - Firmware73
Status - Serial Number73
Status - Meter Readings73
History73
Infrared Connection74
Bluetooth Connection74
Maintenance75
Troubleshooting76
History Entries76
Fuses78
Spare Parts78
Lubricant Recommendation, Lubricant Requirements78
Main Body: -25 to +60°C78
Main Body: -40 to +60°C78
Output Type a and Spindle Drives (Linear Actuators) -40 to +60°C79
Basic Lubricant Service Interval79
Training79
Original Declaration of Incorporation of Partly Completed Machinery80
Declaration of Conformity81
Declaration of Conformity82
Technical Data83
Binary Outputs83
Binary Inputs83
Analog Inputs85
Analog Output86
Auxiliary Voltage Input and Output86
Connections87
Connections for Non Explosion-Proof Version87
Connections for Explosion-Proof Version87
Mode of Operation CM88
Mode of Operation CM03 + QT89
Mode of Operation CM03 + L90
Mode of Operation CM03 + LK91
Miscellaneous91
Technical Data CM0392
Standard Version CM0392
VDC Version CM0392
400 V Version CM0392
Technical Data CM0692
Standard Version CM0692
400V Version CM0693
Technical Data CM1293
Standard Version CM1293
Characteristic Curves94
Characteristic Curves - CM0394
Characteristic Curves - CM0695
Characteristic Curves - CM1296

Related product manuals

SCHIEBEL LK Series

5 pages

SCHIEBEL ACTUSAFE CMFS - Direction of Rotation Handwheel for Closing the Valve, Failsafe Move out

Table of Contents

Related product manuals