Schulte 5 Series - Gearbox Layout and Blade Rotation

182 pages

Save Page as PDF

To Next Page

To Previous Page

ASSEMBLY

XH1500/XH1000 06-24 Assembly Section 3-10

ASSEMBLY

GEARBOX LAYOUT AND BLADE ROTATION

CW Center Rotation - 540/1000 RPM

CCW Center Rotation - 540/1000 RPM

Refer to Parts Book for Part Numbers

Main Page

Osha Training Requirements3
To the Owner/Operator/Dealer5
Table of Contents7
Safety Section11
General Safety Instructions and Practices12
Operator Safety13
General Operating Safety13
Safety Signs13
Crushing Hazards14
Connecting or Disconnecting Implement Safety15
Thrown Objects Hazards16
Mower Operation17
Run over Hazards18
Pto Entanglement Hazards19
Mower Blade Contact Hazards20
High Pressure Oil Leak Hazards21
Electrical Fire Hazards22
Transporting Hazards23
Hazards with Maintenance of Implement24
Blade Inspection25
Parts Information26
Decal Location27
Decal Description30
Federal Laws and Regulations40
Introduction Section41
Equipment Specifications44
Key Operation Points45
Operating Noise Level/Sound Pressure45
General Statement Affecting All Schulte Warranty46
Assembly Section49
General Assembly50
Chain Guards50
Tires51
Hydraulic Circuits52
Wing System52
Phasing System52
Hydraulic Phasing Cylinders53
Rephasing Groove53
Driveline Shield54
Pro Level54
Precision Clevis - C000-36055
Tractor Shaft55
Wiring of Lights56
Manual Winch Kit57
Gearbox Layout and Blade Rotation58
Operation Section59
Operation60
Operator Requirements61
Tractor Requirements62
Tractor Requirements and Capabilities62
ROPS and Seat Belt62
Tractor Safety Devices62
Tractor Horsepower62
Drawbar - Pull Type Mower63
Tractor Hydraulics63
Front End Weight63
Power Take off (PTO)63
Tire Spacing64
Getting on and off the Tractor65
Boarding the Tractor65
Dismounting the Tractor65
Starting the Tractor66
Connecting the Mower to the Tractor66
Connecting the Mower Tongue to the Tractor67
Safety Tow Chain67
Connecting Implement Hydraulic Lines to the Tractor68
Lowering the Cutter69
Setting the Mower70
Leveling Wing71
Setting Deck Pitch71
Driveline Attachment72
Driveline Length Check72
Constant Velocity (CV) Driveline74
Pre-Operation Inspection and Service75
Tractor Pre-Operation Inspection/Service76
Mower Pre-Operation Inspection/Service76
Cutting Component Inspection80
Blade Bolt Inspection82
Driving the Tractor and Mower85
Starting the Tractor86
Brake and Differential Lock Setting86
Operating the Cutter Wings86
Driving the Tractor and Mower87
Crossing Ditches and Steep Inclines88
Operating the Tractor and Implement89
Foreign Debris Hazards90
Bystanders/Passersby Precautions91
Engaging the Power Take off (PTO)91
PTO RPM and Ground Speed92
Operating the Mower92
Roadway Cutting - Blade Rotation95
Roadway Cutting - with Traffic96
Roadway Cutting - against Traffic96
Right of Way (Highway) Mowing97
Shutting down the Implement98
Disconnecting the Mower from the Tractor98
Mower Storage99
Transporting the Tractor and Implement100
Tires and Wheels101
MANUAL WINCH OPERATING INSTRUCTIONS (Winch Optional)102
Locking the Cutter for Transport106
Transporting on Public Roadways107
Safety Chain107
Hauling the Tractor and Implement109
Troubleshooting Guide110
Maintenance Section113
Hazards with Maintenance of Implement114
Parts Information116
Lubrication116
Gearboxes118
Back Beam Cylinder120
Remove Back Beam Cylinder120
Install Back Beam Cylinder121
Wing Cylinder123
Remove Wing Cylinder123
Install Wing Cylinder125
Drivelines127
Shaft Removal127
Center Shaft Removal128
Shaft Installation129
Parts Information129
Wing Shaft Installation129
Center Shaft Installation132
Grease Schedule134
Universal Joint Assemblies134
Tractor Shaft135
Blades136
Blade and Blade Carriers136
Blade Carrier Removal136
Blade Carrier Installation137
Slip Clutches138
Disassembly138
Reassembly139
Hubs and Spindles141
Greasing and Installation141
Tightening Instructions for 517 & 511 Hubs142
Walking Axles142
Tires142
Transport Speed142
Inflation Pressure142
Hydraulics143
Proper Torque for Fasteners143
Nuts and Bolts144

Related product manuals

Schulte FX-209

158 pages

Schulte Titan 5000 II Series

108 pages

Schulte 5 Series - Gearbox Layout and Blade Rotation

Table of Contents

Related product manuals