Schwinn 430 - Equipment Assembly Instructions; Step 1: Attach Front Stabilizer to Frame

8
Console Service Mode
The Console Setup Mode lets you input the date and time, set the units of measurement to either English or Metric,
change the machine type, control the sound settings ( on/ off), or see maintenance statistics (Total Run Hours – for
servicetechnicianuseonly).
1. Hold down the PAUSE/END button and Right button together for 3 seconds while in the Power-Up Mode to go into
the Console Setup Mode.
Note: Push PAUSE/END to exit the Console Setup Mode and return to the Power-Up Mode screen.
2. The Console display shows the Date prompt with the current setting. To change, use the Increase/Decrease buttons
toadjustthecurrentlyactivevalue(ashing).PushtheLeft/Rightbuttonstochangewhichsegmentisthecurrently
activevalue(month/day/year).
3. Push OK to set.
4. The Console display shows the Time prompt with the current setting. Push the Increase/Decrease buttons to adjust
thecurrentlyactivevalue(ashing).PushtheLeft/Rightbuttonstochangewhichsegmentisthecurrentlyactivevalue
(hour / minute / AM or PM).
5. Push OK to set.
6. The Console display shows the Units prompt with the current setting. To change, push OK to start the Units option.
Push the Increase/Decrease buttons to change between “MILES” (Imperial English units) and “KM” (metric units).
Note:IftheunitschangewhenthereisdatainUserStatistics,thestatisticsconverttothenewunits.
7. Push OK to set.
8. The Console display shows the Machine Type prompt with the current setting. Push the Increase/Decrease buttons to
change between “BIKE” and Elliptical (“ELIP”).
9. Push OK to set.
10. The Console display shows the Sound Settings prompt with the current setting. Push the Increase/Decrease buttons
to change between “ON” and “OFF”.
11. Push OK to set.
12. The Console display shows the TOTAL RUN HOURS for the machine.
To go to the next Console Setup Mode prompt, push the OK button.
To enter the Manufacturing Menu (MFG Menu), hold down the PAUSE/END button and Down button together for 3
seconds.TheConsoledisplayshowstheFirmwareVersionstring.PushtheUp/Downbuttonstomovethroughthe
MFG Menu options. Push OK to make a selection.
a. ENTER MFG TEST – This option is intended for use on the manufacturing production line only. It is a chained
series of tests similar to the tests listed below, but optimized to be run on the production line. Use of this chained
test should not be necessary anywhere but on the production line.
b. DEBUG TERMINAL – Not used.
 c. MOVELIFT–Notused.Ifselected,thisoptionshouldnotdamagetheconsole,butalsoshouldnothaveany
noticeable effect.
 d. RESETMFGNVM–Notused.Ifselected,thisoptionshouldnotdamagetheconsole,butalsoshouldnothave
any noticeable effect.
 e. RUNBEEPTEST–Soundseachsystembeep/tone/sequenceinorder.Pressanykeytoexit
f. RUN BUTTON TEST – The Console display shows the function of each button as buttons are pressed. If the
displayshowsanincorrectfunction,theoverlayontheConsolemaybeincorrectforthatmodel.Ifthedisplay
doesnotshowafunction,thermwareversionmaybeincorrect.Nobeepsaresoundedduringthistest.
  Toexitthetest,pushandholdoneofthelongkeysequences(i.e.longPause/End+RightorlongPause/End+
Down).
 g. RUNLEDTEST–DrivesLEDstothefollowingstates:
1. All LEDs On 1 second
2. All LEDs Off 1 second
  3. SequenceSegments1atatime–on1second,off1second