Shimaden SRS11A User Manual


Contents
Request ....................................................................... 1
Preface ........................................................................ 1
1. Safety rules ............................................................. 3
2. Introduction ........................................................... 3
2-1. Preliminary check ...................................................... 3
(1) Model code check .............................................................. 4
(2) Accessories check .............................................................. 4
2-2. Notes on use .............................................................. 4
3. Installation and wiring .......................................... 4
3-1. Installation site (environmental conditions) .............. 4
3-2. Mounting ................................................................... 5
3-3. External dimensions and panel cutout ....................... 5
3-4. Wiring ....................................................................... 6
3-5. Terminal layout ......................................................... 7
3-6. Terminal arrangement table ....................................... 7
3-7. Operation preparations .............................................. 8
4. Names and functions of parts on front panel ...... 9
5. Parameter diagram and setting ......................... 10
5-1. Parameter diagram ................................................... 10
5-2. Display when power is applied ............................... 12
5-3. Switching screens .................................................... 12
(1) Switching screens within screen group 0 ...................... 12
(2) Switching between screen group 0 and screen group 1 ... 12
(3) Switching screens within screen group 1 ......................... 12
(4) Switching to screen group 2 ............................................ 12
(5) Switching screens within screen group 2 ......................... 12
(6) Switching to screen group 3 ............................................ 13
(7) Switching to screen group 4 ............................................ 13
(8) Switching screens within screen group 4 ......................... 13
(9) Set data modification ....................................................... 13
5-4. Auto return function ................................................ 13
5-5. Screen group 0 setting ............................................. 14
(1) Setting target set values (SV) .......................................... 14
(2) Manual setting of control output...................................... 14
(3) Auto tuning (AT) ............................................................. 15
(4) Standby (STBY) / execution (EXE) ................................ 15
(5) Event setting .................................................................... 16
(6) Multi SV (target set values) ............................................. 16
6. Screen explanation and setting items ................ 17
7. Measuring Range Codes ..................................... 24
8. Explanation of functions ..................................... 25
8-1. Events ...................................................................... 25
(1) Alarm action .................................................................... 25
(2) Event standby action selection ........................................ 25
(3) Event selection alarm action diagrams ........................... 25
(4) Output 1 inverted output ................................................. 26
(5) Event status output action ............................................... 26
8-2. Heater break/loop alarm ..........................................26
8-3. P.I.D. .......................................................................26
(1) P (Proportional action) .................................................... 26
(2) I (Integral time) .............................................................. 26
(3) D (Derivative time) ......................................................... 26
(4) MR (Manual reset) ......................................................... 27
(5) SF (Target value function) .............................................. 27
8-4. Control output .........................................................27
(1) Lower limit and higher limit limiter setting .................... 27
(2) Proportional cycling time ............................................... 27
(3) Control output characteristics ......................................... 27
(4) Two-position action ........................................................ 27
8-5. External control input (DI) ......................................28
(1) Controller action execution EXE1 (RUN1) .................... 28
(2) Controller action execution EXE2 (RUN2) .................... 28
(3) Manual output (MAN) .................................................... 28
(4) Auto tuning execution (AT) ............................................ 28
(5) SV external selection (ESV2) ......................................... 28
(6) Output 1 output characteristic (ACT1) ........................... 29
(7) Output 2 output characteristic (ACT2) ........................... 29
(8) Program (PROG) ............................................................ 29
(9) Hold signal (HLD) .......................................................... 29
(10) Advance (ADV) ............................................................ 29
(11) Start pattern external selection 2 bits (PTN2) ............... 29
(12) Start pattern external selection 3 bits (PTN3) ............... 29
(13) Total unlatching (L_RS) ............................................... 29
8-6. Soft start ..................................................................29
(1) Conditions that trigger soft start ..................................... 29
(2) Conditions that cancel soft start ...................................... 29
8-7. Change in position of decimal point ........................30
(1) Change in position of decimal point for linear input ...... 30
(2) Change in position of decimal point of TC/RTD range .. 30
9. Causes and remedy of trouble and errors ......... 30
9-1. Causes and remedy of trouble .................................30
9-2. Causes and remedy of errors ...................................30
(1) Abnormal measured input ............................................... 30
(2) Heater break/loop alarm errors ....................................... 30
10. Parameter mask/lock function ......................... 31
10-1. Overview ...............................................................31
10-2. Parameter diagram .................................................31
10-3. Mask/lock setting contents ....................................32
(1) Settings for various parameters ...................................... 32
(2) Settings for each screen group ........................................ 32
(3) Mask/lock initialization .................................................. 32
11. Parameter setting record .................................. 3 3
12. Specifications ..................................................... 35

Shimaden SRS11A Specifications

General

Brand	Shimaden
Model	SRS11A
Category	Controller
Language	English