Shure AD4D - User Manual

42 pages

To Next Page

AD4D

Dual Channel Receiver

User guide for the Shure AD4D Axient Digital dual channel receiver.

Version: 8.0 (2023-C)

Main Page

Table of Contents2
AD4D Dual Channel Receiver4
IMPORTANT SAFETY INSTRUCTIONS4
Australia Warning for Wireless5
AD4D Axient Digital Two-Channel Wireless Receiver5
- Features5
Included Components6
Mounting Instructions6
Hardware7
- Receiver Front Panel7
- Receiver Back Panel9
Menus and Configuration10
- Accessing the Device Configuration Menu or Channel Menus11
- Home Screen11
- Screen Icons11
- Device Configuration Menu and Parameters12
  - Device Configuration Menu Screen12
  - Device Configuration Menu Map13
- AD4D Device Configuration Parameters13
- Channel Menu Parameters17
Radio Frequency (RF) Settings18
Radio Frequency (RF) Settings19
- Setting the RF Tuning Band19
- IR Sync19
- Setting the Frequency Manually19
- Channel Scan and Group Scan20
  - Channel Scan20
  - Group Scan20
- Requesting a New Frequency from a Spectrum Manager21
- Transmission Modes21
  - Selecting a Transmission Mode21
- Assigning Transmitters to Transmitter Slots22
- Interference Management22
- Channel Quality Meter23
- Frequency Diversity23
- Antenna Bias24
- RF Cascade Ports24
- Firmware24
Audio Settings25
- Adjusting Channel Gain and Audio Output25
- Tone Generator26
- Headphone Monitoring26
  - Headphone Monitoring Options26
- System Gain27
Networking27
- Networking Receivers27
- Network Browser31
- Network Troubleshooting31
Operation31
Operation32
- Assigning a Device ID32
- Assigning a Channel Name32
- Locking and Unlocking the Controls32
- Display Screen Options32
- Saving Receiver Settings as User Presets33
- Programming Transmitters Using IR Presets33
- Encryption33
- Restoring the Receiver to Factory Settings33
- Cooling Fan34
Troubleshooting34
- Power34
- Gain34
- Cables35
- Interface Locks35
- Encryption Mismatch35
- Firmware Mismatch35
- Tx Battery Hot35
- Radio Frequency (RF)35
- Clean Battery Contacts36
Contact Customer Support36
Specifications36
- System Specifications36
- RF Carrier Frequency Range36
- Working Range37
- RF Tuning Step Size37
- Channel-to-Channel Spacing37
- Channel-to-Channel Spacing37
- Image Rejection37
- RF Sensitivity37
- LatencyAnalogOutput37
- Audio Frequency Response37
- Signal-to-Noise Ratio(Dynamic Range)37
- Total Harmonic Distortion37
- System Audio Polarity38
- Operating Temperature Range38
- Storage Temperature Range38
- Audio Output38
- Gain Adjustment Range38
- Configuration38
- Impedance38
- Full Scale Output ( 200K Ωload)38
- Mic/Line Switch38
- Phantom Power Protection38
- Dimensions38
- Weight38
- Housing38
- Power Requirements39
- Thermal Power Dissipation39
- DC Power Requirements39
- Network Interface39
- Network Addressing Capability39
- Maximum Cable Length39
- Cascade Output39
- Connector Type39
- Configuration39
- Impedance39
- Insertion Loss39
- RF Input39
- Spurious Rejection39
- Connector Type39
- Impedance39
- Bias Voltage39
- RF Carrier Frequency Rangemodel dependent40
- Tables and Diagrams40
  - Audio Output40
  - XLR to ¼" Output40
Receiver Frequency Bands40
Certifications41
- Canada Warning for Wireless42

Need help?

Do you have a question about the Shure AD4D and is the answer not in the manual?

Shure AD4D Specifications

General

Number of Channels	2
Dynamic Range	>120 dB, A-weighted
Power Supply	100 to 240 V AC, 50-60 Hz
Audio Output Connectors	XLR
Audio Frequency Response	20 Hz to 20 kHz
Audio THD	<0.3%
Network Interface	Ethernet 10/100 Mbps
Dimensions	44 mm x 483 mm
Audio Output	Balanced XLR, Balanced 1/4" TRS