Siemens PM330 - Page 85

Technical specifications
6.1 General technical data
Power Module PM330
Hardware Installation Manual, 12/2018, A5E32844552B AF
83
Compliance with standards
Standards EN 60146-1-1, EN 61800-2, EN 61800-3, EN 61800-5-1, EN 61800-5-2, EN 60204-1,
EN 60529, EN 61508, EN 61511, EN ISO 13849
UL61800-5-1, CSA 22.2 No. 274-13
CE marking in accordance with EMC Directive No. 2014/30/EU, Low Voltage Directive No. 2014/35/EU
(up to FS < 04) and Machinery Directive No. 2006/42/EC (from FS ≥ 04)
Approval
cULus (File No.: E192450), CE, RCM, EAC, KC, ROHS
Ambient conditions
During storage
3)
During transport
3)
During operation
Ambient temperature -25° … +55° C -25 ... +70 °C
–40 °C permitted for 24 h
0 ... +45 °C
up to + 55 °C with derating
Relative humidity
(no condensation)
Corresponds to class
5 to 95%
1K4 according to
EN 60721-3-1
5 ... 95% at 40° C
2K3 according to
EN 60721-3-2
5 ... 95%
3K3 according to
EN 60721-3-3
Environmental class / harm-
ful chemical substances
1C2 according to
EN 60721-3-1
2C2 according to
EN 60721-3-2
3C2 according to
EN 60721-3-3
Organic/biological influences
(no conductive dust particles
permitted)
1B1 according to
EN 60721-3-1
2B1 according to
EN 60721-3-2
3B1 according to
EN 60721-3-3
Mechanically active sub-
stances
1S1 according to
EN 60721-3-1
2S1 according to
EN 60721-3-2
3S1 according to
EN 60721-3-3
Pollution degree
2 according to EN 61800-5-1
Installation altitude up to 1000 m above sea level without derating,
> 1000 m above sea level with derating (see Chapter Derating as a function of the installa-
tion altitude (Page 100))
Mechanical strength
Oscillation in operation: Test Fc acc. to EN 60068-2-6
10 ... 12.9 Hz with 0.05 g
12.9 ... 57.5 Hz with 0.075 mm Deflection
57.5 ... 200 Hz with 1 g
10 cycles/axis. Single sine sweep. Sweep speed 1 octave/min
1 cycle = start frequency... maximum frequency... start frequency = 2 sweeps.
Oscillation during transport
and storage
3)
:
Test Fc acc. to EN 60068-2-6
5 ... 9.1 Hz with 1.5 mm deflection
9.1 ... 200 Hz with 0.5 g
10 cycles/axis. Single sine sweep. Sweep speed 1 octave/min
1 cycle = start frequency... maximum frequency... start frequency = 2 sweeps.
Shock in operation: Test EA acc. to EN 60068-2-27
Half-sine: 5 g for 30 ms shock duration; 3 shocks per direction (total 18 shocks)
Half-sine: 15 g for 11 ms shock duration; 3 shocks per direction (total 18 shocks)
Shock during transport and
storage
3)
:
Test Fc acc. to EN 60068-2-6
5 ... 9.1 Hz with 1.5 mm deflection
9.1 ... 200 Hz with 0.5 g
10 cycles/axis. Single sine sweep. Sweep speed 1 octave/min
1 cycle = start frequency... maximum frequency... start frequency = 2 sweeps.