Siemens SINUMERIK 804D sl Function Manual

Contents
Mode Group, Channel, Program Operation, Reset Response (K1)
Function Manual, 08/2005 Edition, 6FC5397-0BP10-0BA0
v
5.1.1.1 HMIspecific machine data.......................................................................................................... 5-1
5.1.1.2 NC-specific machine data .......................................................................................................... 5-1
5.1.2 Channel-specific machine data.................................................................................................. 5-2
5.1.2.1 Basic machine data.................................................................................................................... 5-2
5.1.2.2 Block search............................................................................................................................... 5-3
5.1.2.3 Reset response.......................................................................................................................... 5-4
5.1.2.4 Auxiliary function settings .......................................................................................................... 5-4
5.1.2.5 Transformation definitions.......................................................................................................... 5-5
5.1.2.6 Memory settings......................................................................................................................... 5-6
5.1.2.7 Program runtime and workpiece counter................................................................................... 5-7
5.1.3 Axis/spindlespecific machine data ............................................................................................. 5-7
5.2 Setting data................................................................................................................................ 5-7
5.2.1 Channelspecific setting data...................................................................................................... 5-7
5.3 Signals ....................................................................................................................................... 5-8
5.3.1 Signals to NC ............................................................................................................................. 5-8
5.3.2 Signals to mode group ............................................................................................................... 5-8
5.3.3 Signals from mode group........................................................................................................... 5-8
5.3.4 Signals to channel...................................................................................................................... 5-9
5.3.5 Signals from channel ................................................................................................................. 5-9
5.3.6 Signals to axis/spindle ............................................................................................................. 5-10
5.3.7 Signals from axis/spindle ......................................................................................................... 5-10
Index................................................................................................................................................ Index-1
Tables
Table 2-1 Mode change ........................................................................................................................... 2-12
Table 2-2 Effect on program status.......................................................................................................... 2-85
Table 2-3 Responses to operator or program actions ............................................................................. 2-87
Table 2-4 Typical program sequence............................................................................................
........... 2-88
Table 2-5 Sequence when starting a part program.................................................................................. 2-92
Table 2-6 Sequence at part program end ................................................................................................ 2-92
Table 2-7 Sequence with operator panel reset ........................................................................................ 2-93
Table 2-8 Table 1–9 Sequence during power-up..................................................................................... 2-94
Table 2-9 Summary of NCK events, which stop at least for short time ................................................. 2-101
Table 2-10 Program control: Interface signals ......................................................................................... 2-122
Table 2-11 Change system settings by means of MD ............................................................................. 2-135
Table 2-12 Selection of RESET and powerup response ......................................................................... 2-138
Table 2-13 Effect of MD20110 $MC_RESET_MODE_MASK Bits 0 to 6................................................. 2-139
Table 2-14 Effect of MD20110 $MC_RESET_MODE_MASK Bits 7 to 12............................................... 2-139
Table 2-15 Effect of MD20110 $MC_RESET_MODE_MASK Bits 13 to 17 (in SW 6.4 and higher,
Bit 16 to Bit 17)....................................................................................................................... 2-140
Table 2-16 Effect of MD20112 $MC_START_MODE_MASK Bits 1 to 7 ................................................. 2-141
Table 2-17 Effect of MD20112 $MC_START_MODE_MASK Bits 8 to 12 ............................................... 2-142
Table 2-18 Effect of MD20112 $MC_START_MODE_MASK Bits 13 to 17 ............................................. 2-142

Siemens SINUMERIK 804D sl Specifications

General

Brand	Siemens
Model	SINUMERIK 804D sl
Category	Control Systems
Language	English