Siemens SINUMERIK 840D Programming Manual

Index
Job planning
Index-2 Programming Manual, 03/2006 Edition, 6FC5398-2BP10-1BA0
Axial feed, 10-51
Axial master value coupling, 9-31
Axis
Local, 13-45
AXIS, 1-4
Axis container, 13-44, 13-47
Axis coordination, 10-52
Axis positioning, 10-43
Specified reference position, 10-45
Axis replacement
Accept axis, 1-57
AXTOCHAN, 1-58
GET, 1-55
Get and release using synchronized actions, 10-47
Preconditions, 1-57
Release axis, 1-57
Set up variable response, 1-58
without preprocessing stop, 1-58
Without synchronization, 1-56
Axis Replacement
RELEASE, 1-55
AXNAME, 13-1, 13-2
AXSTRING, 1-27, 13-1, 13-2
AXTOCHAN, 1-58
AXTOSPI, 13-1, 13-2
B
B_AND, 1-21
B_NOT, 1-21
B_OR, 1-21
B_XOR, 1-21
B2, 7-16
B3, 7-16
B4, 7-16, 7-22
B5, 7-16, 7-22
Backlash, 13-10
BAUTO, 5-4
Behavior at curve table edges, 9-22
BFRAME, 6-3
Bit logic operators, 1-21
BLOCK, 2-22
Block display, 2-23, 2-36
BNAT, 5-4
BOOL, 1-4
BSPLINE, 5-4
BTAN, 5-4
C
C2, 7-16
C3, 7-16
C4, 7-16, 7-22
C5, 7-16, 7-22
CAC, 5-1
CACN, 5-1
CACP, 5-1
CALCDAT, 14-2, 14-15
Calculate circle data, 14-15
Calculate intersection of two contour elements, 14-2
CALL, 2-21, 2-22
Call by value parameters for technology cycles, 10-71
Calling up a program in ISO language indirectly with
ISOCALL, 2-23
CALLPATH, 2-25, 3-5
CANCEL, 10-2
Cancel synchronized action, 10-77
Cartesian PTP travel, 7-6
CASE, 1-34
CASE statement, 1-34
CDC, 5-1
CFINE, 6-17
CHANDATA, 3-7
Channel-specific frames, 6-27
CHAR, 1-4
CHECKSUM, 1-69
CHKDNO, 8-37
CIC, 5-1
Circumferential milling with limitation surfaces, 8-26
Clamping axis/spindle, 13-44
Clearance control, 10-36
CLEARM, 1-41, 10-60
CLRINT, 1-46
CMIRROR, 1-19, 6-9
COARSE, 13-15
Coarse offset, 6-16
COARSE50, 13-19, 13-21
COARSEA, 5-38
COMCAD, 5-13
Command axes, 10-42
Command elements, 10-3
Comparison and logic operators, 1-20
COMPCURV, 5-13
COMPLETE, 3-6, 3-7
Complete basic frame, 6-29
COMPOF, 5-13, 5-22
COMPON, 5-13, 5-22, 7-45, 9-41
Compressor, 5-12, 5-24
Compressor for orientation
COMPON, COMPCURV, 5-16
Computing capacity, 13-41
Concatenation of strings, 1-28
Conditionally interruptible program sections, 9-44
Configurable parameter ranges, 10-11
Constraints for transformations, 7-76
CONTDCON, 14-2, 14-9
Contour element, 14-5

Siemens SINUMERIK 840D Specifications

General

Series	SINUMERIK 840D
Axes	Up to 31
Channels	Up to 10
Operating System	Windows-based
Power Supply	24 V DC
Control Unit Type	CNC
Interface	Ethernet, PROFIBUS
Display	TFT color display
Interpolation	Spline
PLC	Integrated PLC
Data Storage	CompactFlash, USB