Siemens SINUMERIK 840D Programming Manual

Index
Job planning
Programming Manual, 03/2006 Edition, 6FC5398-2BP10-1BA0
Index-3
Contour elements, intersection, 14-12
Contour preparation, 14-3, 14-9
Relief cut elements, 14-8
Contour table, 14-3, 14-9
CONTPRON, 14-2, 14-3, 14-12, 14-14
Control structures, 1-36
Restrictions, 1-38
Runtime response, 1-37
Conversion routines, 10-10
Corner deceleration at all corners, 5-37
Corner deceleration at inside corners, 5-37
COS, 1-19
COUPDEF, 13-14, 13-17, 13-18
COUPDEL, 13-14, 13-17
Coupled motion, 9-8, 10-54
Coupled-motion axes, 9-10
Coupling factor, 9-11
Coupled-axis combinations, 9-9
Coupling, 9-3, 9-9
Coupling type
AV, 13-15
DV, 13-15
VV, 13-15
COUPOF, 13-14, 13-22
COUPOFS, 13-14, 13-22
COUPON, 13-14, 13-19
COUPONC, 13-14
COUPRES, 13-14, 13-22
cov.com, user cycles, 2-37
CP, 7-69
CPROT, 4-4
CPROTDEF, 4-2
Create interrupt routine as subroutine, 1-47
CROT, 1-19, 6-9
CROTS, 6-15
CS, 9-3
CSCALE, 1-19, 6-9
CSPLINE, 5-4
CTAB, 9-27, 9-28, 9-29
CTABDEF, 9-14, 9-16
CTABDEL, 9-14, 9-18, 9-20
CTABEND, 9-14, 9-16
CTABEXISTS, 9-20
CTABFNO, 9-20
CTABFPOL, 9-21
CTABFSEG, 9-21
CTABID, 9-20
CTABINV, 9-27, 9-28, 9-29
CTABISLOCK, 9-20
CTABLOCK, 9-20
CTABMAX, 9-23
CTABMEMTYP, 9-20
CTABMIN, 9-23
CTABMPOL, 9-21
CTABMSEG, 9-21
CTABNOMEM, 9-20
CTABPERIOD, 9-20
CTABPOLID, 9-21
CTABSEG, 9-20
CTABSEGID, 9-20
CTABSEV, 9-27, 9-28
CTABSSV, 9-27, 9-28
CTABTEP, 9-23
CTABTEV, 9-23
CTABTMAX, 9-23
CTABTMIN, 9-23
CTABTSP, 9-23
CTABTSV, 9-23
CTABUNLOCK, 9-20
CTRANS, 1-19, 6-9, 6-17
Current
Angular offset, 13-23
Coupling status following spindle, 13-23
Current block display, 2-36
Current channel basic frames, 6-29
Current first basic frame in the channel, 6-29
Current NCU-global basic frames, 6-28
Current programmable frame, 6-30
Current settable frame, 6-30
Current system frames, 6-28
Current total frame, 6-30
Curve tables, 9-13, 9-18
Non-periodic curve table, 9-25
Periodic curve table, 9-26
Read in synchronized actions, 9-27
CUT3DC, 8-16, 8-22
CUT3DCC, 8-26
CUT3DCCD, 8-26
CUT3DF, 8-16
CUT3DFF, 8-16
CUT3DFS, 8-16
CUTCONOF, 8-13
CUTCONON, 8-13
Cutting edge number, 8-36
Cycles
Setting parameters for user cycles, 2-31, 2-37
User cycles and manufacturer cycles with NC
programs of the same name, 2-26
Cylinder surface curve transformation, 7-55, 7-56
Offset contour normal OFFN, 7-61
Cylinder surface transformation, 7-6
D
D, 7-56
D numbers
Check, 8-37

Siemens SINUMERIK 840D Specifications

General

Series	SINUMERIK 840D
Axes	Up to 31
Channels	Up to 10
Operating System	Windows-based
Power Supply	24 V DC
Control Unit Type	CNC
Interface	Ethernet, PROFIBUS
Display	TFT color display
Interpolation	Spline
PLC	Integrated PLC
Data Storage	CompactFlash, USB