Siemens SION - Index

Index
9229 0025 176 0E 77
2021-11-15
Index
A
Accessories available for order
............................. 74
Altitude correction factor
....................................... 36
Ambient conditions
................................................ 36
Anti-pumping device (-K1)
.................... 21– 22, 24
Areas of application
.............................................. 15
Auxiliary switch (-S1)
............................ 20– 22, 26
B
Basic equipment
................................................... 22
Bushing
................................................................. 58
C
Cable harness
....................................................... 51
Cable outlet
........................................................... 42
Charging
............................................................... 70
Circuit-breaker shaft cover
............................ 22, 48
Circuit-breaker tripping signal (-S6)
...... 20– 22, 27
CLOSE pushbutton
....................................... 19, 70
Closing lock-out (-Y8E), electrical
......... 21– 22, 33
Closing solenoid (-Y9)
........................... 20– 22, 24
Closing spring
............................... 20– 21, 71– 72
Conductor bar
....................................................... 54
Connection thread
................................................. 54
Connector strip
(Q0-X1.1, Q0-X1.2, Q0-X1.3)
......................... 22
20-pole
............................................................ 50
30-pole
............................................................ 50
Contact arm
.......................................... 55– 56, 62
Contact arm adapter
............................................. 56
Contact surface, pole
............................................ 54
Contact system
..................................... 18, 56– 57
Contacts
1250 A, third-party provider
............................ 58
Cover
............................................ 17– 19, 40, 70
Insulating material
.......................................... 19
Metal
............................................................... 19
mounting
......................................................... 40
removing
......................................................... 40
D
Dielectric strength
................................................. 36
Disconnected position
................................... 31, 65
Dowel pin
.............................................................. 54
E
Earthing terminal
................................................... 49
H
Hand crank
............................................................ 72
for manual charging of the closing spring
....... 19
Siemens withdrawable part
............................ 65
third-party withdrawable part
.......................... 67
Hand crank coupling
..................................... 19– 21
Heater (-R01)
........................................ 20– 22, 31
High-voltage protective earth
................................ 49
I
Installation altitudes
.............................................. 36
Installation position
................................................ 39
Insulated operating rod
.......................................... 19
Insulating shell
.............................................. 17– 18
mounting
................................................ 43– 44
Insulator
........................................................ 17– 18
Interlock, mechanical
.................................... 22, 31
Interlocks
............................................................... 31
Intermediate position
............................................. 65
K
Key-operated interlock
.......................... 19– 22, 33
L
Low-voltage
interface (-X0)
........................................ 22, 50
plug connector (-X0)
............... 17– 18, 20– 21
M
Manual closing, mechanical
.................................. 22
Manual opening, mechanical
................................. 22
Mating contact
....................................................... 58
Motor (-M1)
................................................... 20– 23
Motor short-circuit protection
................................. 23
N
Name plate
........................................... 17– 18, 34
O
OPEN pushbutton
......................................... 19, 70
Opening spring
...................................................... 70
Operating mechanism
........................................... 19
Operating position
................................................. 31
Operations counter
....................................... 19– 22
P
Plug
(-Q0)
................................................................ 51
(Q0-X1)
.................................................. 20– 21
(-Q1)
................................................................ 51
(-X01) and (-X02)
................................... 20– 21
withdrawable part
............................................ 51
Pole contact plate
......................................... 17– 18
Pole head
..................................................... 17– 18
Pole shell
.............................................. 17– 18, 43
Pole-centre distance
..................................... 34– 35
Position indicator
................................................... 70
Position indicator CLOSED-OPEN
............... 19– 21
Position queries
..................................................... 65
Position switch
....................................................... 25
(-S12)
..................................................... 20– 22
(-S21)
............................................. 20– 22, 25
(-S3)
............................................... 20– 22, 25
(-S4)
............................................... 20– 22, 25
(-S5)
................................................................ 22
(-S6)
............................................... 20– 21, 27
Pressure plate
....................................................... 22
Protective plate
...................................................... 46
angled at the top
............................................. 46
both sides
........................................................ 46
continuous, between pole and operating