EasyManua.ls Logo

Smeg SW262 - User Manual

Smeg SW262
37 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
SMEG thanks you for choosing one of
its products.
Read all the instructions in this manual carefully to become familiar with the right
conditions for the proper use of your dishwasher.
This manual is an integral part of the dishwasher and must always be kept intact together with the
appliance. Before using the appliance, please read this manual throughout. Installation must be done
by qualified staff in compliance with the relevant regulations. The appliance is intended for
professional use, and complies with Directives 2006/95 EC and 2004/108 EC, including the prevention
and elimination of RF disturbance. The appliance is built to provide the following function: Washing
and drying dishes; all other uses are to be considered improper. The manufacturer declines all
liability for uses other than those stated above.
1 PRODUCT IDENTIFICATION AND SAFETY AND OPERATING WARNINGS
1.1 Brand and model (or type)
Professional dishwasher
Brand: Smeg
Model: SW260/262
1.2 Edition (revision) of user manual
19 390 5043 04
10/05/2016
Rev. of manual
Date
1.3 Name and address of manufacturer/distributor
Smeg S.p.A.
Via Leonardo da Vinci, 4 - 42016 Guastalla (RE) Tel. +39 0522 8211 - Fax + 39 0522 821453 website:
www.smegfoodservice.com, email : foodservice@smeg.it
Info :
INFORMATION AND SERVICE FOR SMEG PROFESSIONAL DISHWASHER PRODUCTS
Our Sales Department staff will be able to provide you with information about prices and special offers.
Our After-Sales Department will be able to provide you with guidance about keeping your appliance
functioning correctly and put you in touch with your nearest authorised Service Centre. Our entire product
offering can be viewed at the above website.
1.4 Declaration of conformity to product standards
This appliance is marked in compliance with European Directive 2002/96/EC on waste electrical and electronic
equipment (WEEE). Make sure that this product is scrapped correctly to safeguard the environment and
health. Decommission the appliance in compliance with local waste management regulations. For further
information on the treatment, recovery and recycling of this product, contact the local authority, domestic
waste collection service, or your Smeg reseller. The appliance must be connected to earth in compliance with
electrical safety (CEI-EN-IEC 60335-2-58/61770) and electromagnetic compatibility regulations (CEI-IEC-EN
55014-1/-2, 61000-3;4, 50366). The manufacturer is not liable for any injury or damage cause by failure to
comply with the instruction given in this manual, improper use, tampering with even a single part of the
appliance, or the use of non-original spare parts.

Table of Contents

Other manuals for Smeg SW262

Preview: Translation Of The Original Instructions
Translation Of The Original Instructions41 pages

Questions and Answers

  • S
    steven60Sep 18, 2025
    What does A:93 error mean on Smeg Dishwasher?
    • K
      Kaitlin GonzalesSep 18, 2025
      If your Smeg dishwasher displays alarm A:93 indicating machine maintenance is needed, the machine has exceeded the set number of hours of operation since installation or its last service. Contact technical service for routine maintenance. You can press Start/Pause to ignore the warning and continue using the machine.
  • J
    James GarciaAug 25, 2025
    What does AF:01 error mean on Smeg Dishwasher?
    • A
      Austin JacksonAug 25, 2025
      If your Smeg dishwasher displays alarm ID AF:01 because the water does not heat to temperature in the set time, run the DEFAULT PROCEDURE. If the alarm does not reset, run the RESTORE PROCEDURE.
  • A
    annette91Aug 26, 2025
    How to fix Smeg SW262 that won't start?
    • P
      pruittzacharyAug 26, 2025
      If your Smeg dishwasher program won't start, ensure the dishwasher is connected to the mains and there is no power outage. Also, make sure the water cock is open and the dishwasher door is properly closed.
  • V
    Veronica AlvarezAug 27, 2025
    What to do if water is left in my Smeg SW262?
    • S
      sheena51Aug 27, 2025
      If water remains inside your Smeg dishwasher after a cycle, check that the drain hose is not kinked, the drain trap is not blocked, and the dishwasher filters are not clogged.
  • T
    Troy Dunn DDSSep 19, 2025
    What does AF:96 error mean on Smeg SW262 Dishwasher?
    • B
      bernarddillonSep 22, 2025
      If your Smeg dishwasher displays alarm AF:96 indicating a tank water level anomaly, check the water intake and drain fittings and ensure they comply with specifications. If you notice any leaks around the appliance, close all water cocks. Run the DEFAULT PROCEDURE. If the alarm does not reset, run the RESTORE PROCEDURE.
  • M
    Michael SchultzSep 23, 2025
    Why is my Smeg SW262 Dishwasher leaving streaks on dishes?
    • D
      Daisy AndersonSep 23, 2025
      If your tableware is streaky or stained after a wash in your Smeg dishwasher, check that the rinse aid dispenser setting is not too high.
  • R
    Rhonda NunezSep 9, 2025
    What does AF:34 error mean on Smeg SW262 Dishwasher?
    • S
      stephensonashleySep 9, 2025
      If your Smeg dishwasher displays alarm AF:34 indicating the steam condenser does not drain water, check the drain hookup for height and position of drain fittings. Also, check hookup, as specified in this manual and check for obstructions and restrictions along the hoses. Run the DEFAULT PROCEDURE. If the alarm does not reset, run the RESTORE PROCEDURE.
  • K
    Kimberly JacobsSep 12, 2025
    What does AF:54 error mean on Smeg Dishwasher?
    • R
      Ryan RobinsonSep 12, 2025
      If your Smeg dishwasher displays alarm AF:54 indicating the door was detected open during the cycle, make sure to close the door properly before running a wash cycle. Do not force the door open during a cycle; always use the appliance's controls to pause the cycle and open the door. Also, make sure there are no objects jammed between the door and the dishwasher chamber which are stopping the door closing. Run the DEFAULT PROCEDURE. If the alarm does not reset, run the RESTORE PROCEDURE.
  • S
    Scott JonesSep 3, 2025
    What does AF:09 error mean on Smeg SW262?
    • C
      Christopher MoralesSep 3, 2025
      If your Smeg dishwasher displays alarm ID AF:09 because partial draining has not succeeded, run the DEFAULT PROCEDURE. If the alarm does not reset, run the RESTORE PROCEDURE.
  • T
    Tammy HallSep 1, 2025
    What does AF:05 error mean on Smeg Dishwasher?
    • J
      John PalmerSep 1, 2025
      If your Smeg dishwasher displays alarm ID AF:05 because the operating temperature sensor TL1 has generated an anomalous signal, run the DEFAULT PROCEDURE. If the alarm does not reset, run the RESTORE PROCEDURE.

Summary

1 Product Identification and Safety Warnings

2 Product Characteristics

2.1 Application and intended use

Details the dishwasher's intended professional use and general functions.

2.2 Dimensions and handling instructions

2.3 Technical characteristics

2.3.1 Electrical connections

Outlines electrical connection requirements, including power supply and thermal cutout.

2.3.2 Plumbing connections

Describes water supply and drain connections, including types and water temperature.

2.4 Drain hose connections

2.8 Safety precautions and instructions

4 Preparing the Appliance for Use

4.1 Removing the packaging, inspection

4.3 Installing the appliance

4.4 Preliminary settings and adjustments

4.6 Precautions before use

5 Operating Information and Instructions

5.1 Safe use

Key safety information for operating the professional dishwasher.

5.2 Using the water softener

5.3 Using detergent and rinse aid

5.3.1 Correct use of peristaltic pumps

5.4 Description of controls and wash programs

5.4.1 Controls

Overview of the control panel layout and symbols for different dishwasher models.

5.4.2 Detailed description

Detailed explanation of the function of each button on the control panel.

5.5 Indicator light - Meaning

5.6 Loading tableware

5.7 Height adjustment of the upper basket

5.7.1 Adjustment procedure

5.8 Setting the wash program

5.8.1 Models SW262

Details wash programs, soiling types, detergent amounts, and sequences for SW262 models.

5.8.2 Models: SWT262

Details wash programs, soiling types, thermal disinfection, and sequences for SWT262 models.

5.8.3 Model SWT260 X e SWT260

Details wash programs, soiling types, detergent, and sequences for SWT260X/SWT260 models.

5.9 Drying cycle

5.12 Selecting the washing program

5.12.1 Perform resins regeneration

5.13 Interrupting a running program

5.14 Reset procedure

5.14.1 Running a RESET procedure

Procedure for resetting the dishwasher in case of malfunction or interrupted programs.

6 Setup Mode and Functions

6.1 Entering set-up mode

6.1.1 Entering the USER menu

6.1.2 SET menu

6.1.3 Parameter SET 3

6.1.4 Cloc menu

7 Cleaning and Routine Maintenance

7.1 General precautions

7.2 Description of maintenance by operator

7.3 Cleaning the appliance and its parts

7.5 Diagnostics, reporting and troubleshooting

7.5.1 Eliminating small faults

Troubleshooting guide to resolve common minor problems with the dishwasher.

7.5.2 Alarms

List of dishwasher alarms, their meanings, and recommended user actions for resolution.

Smeg SW262 Specifications

General IconGeneral
TypeFreestanding
Number of place settings13
Noise level47 dB(A)
Half Load OptionYes
ColorWhite
Dimensions (H x W x D)60 cm

Related product manuals