Smeg SW262 - User Manual

37 pages

Save Page as PDF

To Next Page

SMEG thanks you for choosing one of

its products.

Read all the instructions in this manual carefully to become familiar with the right

conditions for the proper use of your dishwasher.

This manual is an integral part of the dishwasher and must always be kept intact together with the

appliance. Before using the appliance, please read this manual throughout. Installation must be done

by qualified staff in compliance with the relevant regulations. The appliance is intended for

professional use, and complies with Directives 2006/95 EC and 2004/108 EC, including the prevention

and elimination of RF disturbance. The appliance is built to provide the following function: Washing

and drying dishes; all other uses are to be considered improper. The manufacturer declines all

liability for uses other than those stated above.

1 PRODUCT IDENTIFICATION AND SAFETY AND OPERATING WARNINGS

1.1 Brand and model (or type)

Professional dishwasher

Brand: Smeg

Model: SW260/262

1.2 Edition (revision) of user manual

19 390 5043 04

10/05/2016

Rev. of manual

Date

1.3 Name and address of manufacturer/distributor

Smeg S.p.A.

Via Leonardo da Vinci, 4 - 42016 Guastalla (RE) Tel. +39 0522 8211 - Fax + 39 0522 821453 website:

www.smegfoodservice.com, email : foodservice@smeg.it

Info :

INFORMATION AND SERVICE FOR SMEG PROFESSIONAL DISHWASHER PRODUCTS

Our Sales Department staff will be able to provide you with information about prices and special offers.

Our After-Sales Department will be able to provide you with guidance about keeping your appliance

functioning correctly and put you in touch with your nearest authorised Service Centre. Our entire product

offering can be viewed at the above website.

1.4 Declaration of conformity to product standards

This appliance is marked in compliance with European Directive 2002/96/EC on waste electrical and electronic

equipment (WEEE). Make sure that this product is scrapped correctly to safeguard the environment and

health. Decommission the appliance in compliance with local waste management regulations. For further

information on the treatment, recovery and recycling of this product, contact the local authority, domestic

waste collection service, or your Smeg reseller. The appliance must be connected to earth in compliance with

electrical safety (CEI-EN-IEC 60335-2-58/61770) and electromagnetic compatibility regulations (CEI-IEC-EN

55014-1/-2, 61000-3;4, 50366). The manufacturer is not liable for any injury or damage cause by failure to

comply with the instruction given in this manual, improper use, tampering with even a single part of the

appliance, or the use of non-original spare parts.

Main Page

Other manuals for Smeg SW262

Translation Of The Original Instructions41 pages

Questions and Answers

T
Tammy HallSep 1, 2025
What does AF:05 error mean on Smeg Dishwasher?
- J
  John PalmerSep 1, 2025
  If your Smeg dishwasher displays alarm ID AF:05 because the operating temperature sensor TL1 has generated an anomalous signal, run the DEFAULT PROCEDURE. If the alarm does not reset, run the RESTORE PROCEDURE.
P
Patricia RhodesAug 31, 2025
What does AF:29 error mean on Smeg SW262 Dishwasher?
- A
  amysimmonsAug 31, 2025
  If your Smeg dishwasher displays alarm AF:29 indicating the tank does not drain in the set time, check the drain connection, especially the height of the drain fittings in relation to specifications, and check for kinks and restrictions along the drain hose. Also, clean the filter unit.
P
Preston JohnstonAug 30, 2025
What does AF:23 error mean on Smeg Dishwasher?
- K
  kathrynturnerAug 30, 2025
  If your Smeg dishwasher displays alarm AF:23 indicating not enough water, run the checks and procedures specified in AF:11. Also check for leaks around the machine. If you find any leaks, immediately close all supply cocks and contact technical service.
J
jevansAug 29, 2025
What does AF:12 error mean on Smeg Dishwasher?
- J
  Jacqueline SmithAug 29, 2025
  If your Smeg dishwasher shows alarm AF:12 indicating no hot water, check that the intake cock is open, check the water supply pressure, and check the position of the intake hoses. You can also run the DEFAULT PROCEDURE; if the alarm persists, run the RESTORE PROCEDURE.
D
Donald Cooper Jr.Aug 28, 2025
What does AF:11 error mean on Smeg SW262?
- T
  tsmithAug 28, 2025
  If your Smeg dishwasher shows alarm AF:11 indicating no cold water during the fill cycle, check that the intake cock is open, check the water supply pressure, and check the position of the intake hoses. You can also run the DEFAULT PROCEDURE; if the alarm persists, run the RESTORE PROCEDURE.
J
Jennifer GarciaAug 27, 2025
Why isn't my Smeg SW262 Dishwasher drying properly?
- V
  vfrostAug 27, 2025
  If your tableware isn't drying properly or remains matt in your Smeg dishwasher, check that the intake filters rinse aid are clean and the rinse aid container is not empty. Ensure the rinse aid dispenser setting is correct, the detergent used is of good quality, and the salt container cap is properly closed.
V
Veronica AlvarezAug 27, 2025
What to do if water is left in my Smeg SW262?
- S
  sheena51Aug 27, 2025
  If water remains inside your Smeg dishwasher after a cycle, check that the drain hose is not kinked, the drain trap is not blocked, and the dishwasher filters are not clogged.
A
annette91Aug 26, 2025
How to fix Smeg SW262 that won't start?
- P
  pruittzacharyAug 26, 2025
  If your Smeg dishwasher program won't start, ensure the dishwasher is connected to the mains and there is no power outage. Also, make sure the water cock is open and the dishwasher door is properly closed.
J
James GarciaAug 25, 2025
What does AF:01 error mean on Smeg Dishwasher?
- A
  Austin JacksonAug 25, 2025
  If your Smeg dishwasher displays alarm ID AF:01 because the water does not heat to temperature in the set time, run the DEFAULT PROCEDURE. If the alarm does not reset, run the RESTORE PROCEDURE.