Software House RM-DCM-2 User Manual

1
RM-DCM-2
Quick Start
Installation Guide
Version H0
Document Part Number UM-215
March 2018
OVERVIEW
The RM-DCM-2 is a UL294 Listed and UL1076 Listed door control
module that includes the RM-4E Reader Module (RM-4E) and enclosure.
The RM-DCM-2 is designed to support up to two RM-4E modules,
providing a single enclosure for doors with IN and OUT readers.
The enclosure also has space for up to three I/8 and/or R/8 boards, for a
total of four boards. The RM-DCM-2 supports an optional battery (12
VDC, 4A), which will be recharged by the RM-4E battery charging circuit.
The RM-4E board provides the hardware interface between Magnetic
signaling read heads or Wiegand signaling read heads and the apC/8X,
iSTAR, and iSTAR Pro hardware. The RM-4E also provides inputs and
outputs that communicate between door components and the apC/8X,
iSTAR, and iSTAR Pro hardware.
The I/8 module provides eight supervised inputs and the R/8 module
provides eight dry contact, Form C relay outputs.
The RM-DCM-2 system consists of two subassemblies:
 Model RM-DCM-CAN enclosure
 Model RM-4E board
NOTE For information about the RM-4E, I/8, or R/8 modules, refer to the Quick
Start guides listed in Table 13.
NOTE All interconnecting products or devices must be UL Listed.

Software House RM-DCM-2 Specifications

General

Brand	Software House
Model	RM-DCM-2
Category	Security System
Language	English

Summary

RM-DCM-2 System Overview

RM-DCM-2 Unit Description

RM-DCM-2 Features

Lists key features like LED status, Maglock, Bypass, and battery charger.

RM-DCM-2 Optional Equipment

Describes optional equipment for the RM-DCM-2, including backup battery and LCD components.

RM-4E Read Head Interfaces

Explains how to interface Wiegand or Magnetic read heads with the RM-4E board.

RM-DCM-2 Tamper Switch Configuration

Details the RM-DCM-2's tamper switch functionality, connection, and configuration.

RM-4E Reader Interface

RM-4E Components Overview

Details the components and layout of the RM-4E board, including connectors, switches, and LEDs.

RM-4E Power Input Methods

Describes two methods for powering the RM-4E: via Power In connector or RS-485 connector.

RM-4E Battery Connection

Explains how to connect the 12 VDC battery for memory retention and charging.

RM-4E Typical LED Scenarios

Provides scenarios for wiring LEDs for different read head types (Bi-Color, Red/Green, Red/Green/Yellow).

RM-4E RS 485 Reader Bus

Explains the RS 485 reader bus connection to apC or iSTAR, including pinout details.

RM-4E Wiegand Signaling

Provides the pinout for Wiegand signaling and the required DIP switch setting.

RM-4E Magnetic (ABA) Signaling

Provides the pinout for Magnetic (ABA) signaling and the required DIP switch setting.

RM-4E Lock Components

Describes lock components on the RM-4E for connecting magnetic and electric strike locks.

RM-4E Lock Connector Pinouts

Shows the pinouts for the Lock Connectors on the RM-4E board.

RM-4E Lock Wiring Configurations

Magnetic Lock Wiring Details

Describes the normal state of magnetic locks and the requirement for bypass switches.

Connecting Magnetic Locks

Provides an example of connecting power supply, magnetic lock, and bypass switch.

Electric Strike Wiring Basics

Explains that electric strike locks typically lock when unpowered and unlock when powered.

Wiring Electric Strikes with Relay 1

Details wiring an electric strike using Relay 1, mentioning tie points and power supply.

RM-4E Input Configuration and Status

RM-4E Input Connections

Explains connecting inputs using standard Software House supervision for NO or NC configurations.

RM-4E LED Input Status Indicators

Describes the meaning of Red, Green, and Yellow LEDs indicating input status (alert, secure, error).

RM-4E SW 5 DIP Switch Configuration

Details the functions of DIP switch SW5 on the RM-4E, relating it to SW3 on RM-4.

RM-4E Reader LED Control

RM-4E Three Wire LED Control

Details wiring for three-wire LED control using Red, Green, and Yellow LED drives.

RM Reader LED Indications

Lists the RM reader LED indications for various conditions like power up, access granted, and alarms.

RM-4E External Bi-color LED Control

Explains external bi-color LED control using two wire (Red/Green) connections.

RM-4E One Wire Yellow LED Control

Describes wiring for one-wire LED control where the Yellow drive is used.

RM-4E One Wire (A,B,C) LED Control

Explains One Wire (A,B,C) mode for single LED read heads, detailing drive wiring and results.

RM-DCM-2 Installation Requirements

RM-DCM-2 Enclosure Installation

Provides guidance on selecting a suitable installation location and mentions enclosure dimensions.

RM-4E, R/8, I/8 Module Dimensions

Shows the dimensions and mounting hole locations for RM-4E, R/8, and I/8 modules.

Mounting RM-4E, R/8, I/8 Boards

Details how to mount RM-4E, R/8, and I/8 boards in the enclosure using screws and washers.

RM-DCM-2 Power Supply and Wiring

Discusses power supply requirements and wiring considerations based on module current draw and wiring length.

RM-DCM-2 Environmental Specifications

Specifies operating temperature ranges and humidity for the RM-DCM-2 and its suitability for indoor use.

RM-DCM-2 Technical Specifications

RM-DCM-2 Software and Firmware Support

Lists the C•CURE software and firmware versions that support RM-DCM-2 components.

RM-4E Power Requirements and Specifications

Details power requirements and operating specifications for the RM-4E board.

RM-DCM-2 Parts List and Compliance

RM-DCM-2 Physical Dimensions and Weight

Lists the physical dimensions and weight of the RM-DCM-2 enclosure.

RM-DCM-2 Compliance and Certifications

Lists the standards and certifications the RM-DCM-2 has been tested and certified for.

RM-DCM-2 Testing Procedures

RM-DCM-2 Testing Required Equipment

Lists the necessary equipment for testing the RM-DCM-2, such as resistors, LEDs, and a multimeter.

RM-DCM-2 Pre-Test Configuration

Outlines configuration steps needed before testing the RM-DCM-2, like installing RM-4E and LCD.

RM-4E Self-Test Mode Operation

Explains how to run the RM-4E's built-in self-test mode, including LED connections and switch settings.

RM-DCM-2 Manual Test Procedure

Provides a step-by-step guide to manually test the RM-DCM-2, checking voltage, communication, inputs, and outputs.