Sony BDP-S550 - Audio Output Signal Chart; Audio Signal Compatibility by Connection

Audio Output Signals
The audio output differs as follows, depending on the source, output jack, and the selected
settings.
LPCM 2ch LPCM 2ch 5.lch
2ch
LPCM 2ch LPCM 2ch 7.lch
2ch
LPCM 2ch
Dolby Digital!
LPCM
2ch 5.lch
2ch
LPCM
2ch*6
LPCM 2ch
Dolby Digital!
LPCM 2ch 7.lch
2ch
LPCM
2ch*6
LPCM 2ch
Dolby Digital!
LPCM 2ch 7.lch 2ch
LPCM
2ch*6
LPCM 2ch
DTS!
LPCM 2ch
5.lch 2ch
LPCM
2ch*6
LPCM 2ch
DTS!
LPCM 2ch
7.lch 2ch
LPCM
2ch*6
LPCM 2ch
DTS!
LPCM2ch 7.lch 2ch
LPCM
2ch*6
LPCM 2ch
LPCM 2ch LPCM 2ch 2ch 2ch
Dolby Digital
LPCM 2ch Dolby Digital LPCM 2ch
5.lch 2ch
DTS
LPCM 2ch DTS LPCM 2ch 5.1ch
2ch
LPCM LPCM 2ch LPCM 2ch
LPCM
2ch 2ch
2ch
DTS LPCM 2ch DTS
LPCM 2ch 5.lch 2ch
66
*1 When "Audio Output Priority" is set to "Stereo
Analog," LPCM 2ch signals are output from
each jack.
*2 When "Audio OutputPriority" is set to "HDMI,"
"CoaxiaUOptical"
or "Multi Channel Analog,"
LPCM 2ch signals are output from jacks other
than the selected jack.
*3 Auto: when "Audio (HDMl)" is set to "Auto" in
the "Audio Settings" setup (page 49).
2ch PCM: when "Audio (HDMl)"
is set to "2ch
PCM" in the "Audio Settings" setup (page 49).
*4 Bitstream: when "Dolby Digital" is set to
"Dolby Digital"
or "DTS" is set to "DTS" in the
"Audio Settings" setup (page 46).
*S When "BD Audio Setting" is set to "Direct,"
audio recorded by the source
is output by
bitstream. However, this audio may be output as
follows depending on the audio formats
supported by the AV amplifier (receiver).
- When the AV amplifier (receiver) does not
support HD Audio (Dolby Digital Plus, Dolby
TrueHD, DTS-HD High Resolution Audio and
DTS-HD Master Audio) but supports Multi-ch
LPCM, up to LPCM
7.1 ch is output.
- When the AV amplifier (receiver) does not
support HD Audio
or Multi-ch LPCM but
supports Dolby Digital/DTS, a Dolby Digital
or DTS bitstream is output.
- When the AV amplifier (receiver) does not
support HD Audio, Multi-ch LPCM
or Dolby
Digital/DTS, LPCM 2ch
is output.
*6 The 2-channel or less-channel primary/
secondary audio signals are output as LPCM 2ch
signals.
"
When outputting 480i/480p video signals from the
HDMI OUT jack, Dolby TrueHD and DTS-HD
Master Audio are output as LPCM, Dolby Digital,
or DTS bitstream signals even if "BD Audio
Setting" is set to "Direct"
in the "Audio Settings"
setup (page 49).