Sony DCR-HC39E - Node Unique ID No. Input

6-47
DCR-HC39E/HC41/HC42/HC42E/HC43/HC43E
3. Node Unique ID No. Input
Write the serial No. and model code to the EEPROM (nonvolatile
memory).
In writing the serial No., a decimal number should be converted
into a hexadecimal number.
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Perform “Node Unique ID No. Input” if the data on page
C has been cleared and the node unique ID No. is not
found.
1) Select page: 0, address: 01, and set data: 01.
2) Read the serial No. from the model name label, and it is as-
sumed to be D
1
.
Example: If serial No. is “77881”,
D
1
= 77881
3) From Table 6-3-2, obtain D
2
and H
1
that correspond to D
1
.
Example: If D
1
= 77881,
D
2
= D
1
– 65536 = 12345
H1 = FE
D
1
(decimal) D
2
(decimal) H
1
(hexadecimal)
(Service model code)
00001 to 65535 D
1
FE
65536 to 131071 D
1
– 65536 FE
131072 to196607 D
1
– 131072 FE
196608 to 262143 D
1
– 196608 FE
262144 to 327679 D
1
– 262144 FE
327680 to 393215 D
1
– 327680 FE
393216 to 458751 D
1
– 393216 FE
458752 to 524287 D
1
– 458752 FE
524288 to 589823 D
1
– 524288 FE
589824 to 655359 D
1
– 589824 FE
655360 to 720895 D
1
– 655360 FE
720896 to 786431 D
1
– 720896 FE
786432 to 851967 D
1
– 786432 FE
851968 to 917503 D
1
– 851968 FE
917504 to 983039 D
1
– 917504 FE
983040 to 999999 D
1
– 983040 FE
Table 6-3-2
4) Enter H
1
to address: E5 on page: C.
Example: If H
1
= FE,
select page: C, address: E5, and set data: FE, then press the
PAUSE button.
5) From Table 6-3-3, obtain the maximum decimal number less
than D
2
, and it is assumed to be D
3
.
Example: If D
2
= 12345.
D
3
= 12288
6) From Table 6-3-3, obtain a hexadecimal number that corre-
sponds to D
3
, and it is assumed to be H
3
.
Example: If D
3
= 12288,
H
3
= 3000
7) Caluculate D
4
using following equations (decimal
caluculation). (0
D
4
225)
D
4
= D
2
– D
3
Example: If D
2
= 12345 and D
3
= 12288,
D
4
= 12345 – 12288 = 57
8) Convert D
4
into a hexadecimal number to obtain H
4
. (See Table
6-4-1 “Hexadecimal - decimal conversion table” in 6-4. Ser-
vice Mode)
Example: If D
4
= 57,
H
4
= 39
9) Enter higher two digits of H
3
to address: E6 on page: C.
Example: If H
3
= 3000,
select page: C, address: E6, and set data: 30, then press the
PAUSE button.
10) Enter H
4
to address: E7 on page: C.
Example: If H
4
= 39,
select page: C, address: E7, and set data: 39, then press the
PAUSE button.
11) Select page: 0, address: 01, and set data: 00.
Page C
Address E5, E6, E7