Stanley Avdel PB2500N NeoBolt Tool - Namjena; Nosna Oprema; Upotreba I Podešavanje Alata

11
HRVATSKI
Tvrtka STANLEY Engineered Fastening teži stalnom razvoju i poboljšavanju svojih proizvoda te
zadržava pravo promjene specikacija bilo kojeg proizvoda bez prethodne najave.
3. UPOTREBA I PODEŠAVANJE ALATA
3.1 NAMJENA
Alati PB2500N predviđeni su SAMO za postavljanje zakovica NeoBolt tvrtke STANLEY Engineered Fastening.
Ovo je profesionalni električni alat. NE dopustite djeci da dolaze u kontakt s alatom. Neiskusni korisnici ovog
alata moraju biti pod nadzorom.
PRIJE PRVE UPOTREBE ALATA PROČITAJTE SVE SIGURNOSNE UPUTE I UPOZORENJA.
Prilikom upotrebe opreme za postavljanje UVIJEK nosite odobrenu zaštitu za vid i sluh
UPOZORENJE: Nemojte modicirati električni alat ni bilo koji njegov dio. Može doći do
ozljeda i materijalne štete.
NEMOJTE koristiti u vlažnim uvjetima ili u prisutnosti zapaljivih tekućina i plinova.
Zaštita od električne struje
Elektromotor predviđen je samo za jedan napon. Uvijek provjerite odgovara li napon baterije naponu na
nazivnoj oznaci. Također provjerite odgovara li napon punjača naponu strujne utičnice.
UPOZORENJE: Prije podešavanja alata uvijek izvadite bateriju.
3.2 NOSNA OPREMA
Uklanjanje nakovnja (sl. 1a).
• Otpustite i uklonite pričvrsnu maticu (D) te
uklonite nakovanj/nosno kućište s alata
• Pomoću ključa od 24 mm odvrnite nakovanj
(B) s nosnog kućišta
• Postavite nakovanj obrnutim redoslijedom.
Uklanjanje obujmice s alata (sl. 2)
• Pritisnite prednje pričvrsnice kvačila.
• Potpuno odvrnite obujmicu s prilagodnika
povlačne glave.
• Da biste postavili obujmicu, pritisnite
pričvsnice kvačila i potpuno zavrnite obujmicu.
NAPOMENA: NEMOJTE UPOTREBLJAVATI KLJUČEVE ZA
ZATEZANJE OBUJMICE.
11
ENGLISH
WARNING: To reduce the risk of serious personal injury, disconnect battery pack before making
any adjustments or removing/installing attachments or accessories.
STANLEY Engineered Fastening policy is one of continuous product development and improvement
and we reserve the right to change the speci cation of any product without prior notice.
3. TOOL USE & SETUP
3.1 INTENDED USE
PB2500N tools are designed for installation of STANLEY Engineered Fastening Neobolt fasteners ONLY.
This tool is a professional power tool. Do NOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
READ ALL SAFETY WARNINGS AND INSTRUCTIONS BEFORE PUTTING TOOL INTO
SERVICE.
ALWAYS wear approved hearing and eye protection at all times when using installation
equipment
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.
DO NOT use under wet conditions or in presence of ammable liquids or gases.
Electrical Safety
The electric motor has been designed for one voltage only. Always check that the battery pack voltage
corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds
to that of your mains.
WARNING: Before adjusting tool, always remove the battery pack.
Before Use
•Install relevant size nose equipment •
• Ensure that the battery is fully charged
• Insert Battery Pack into the tool
• Quickly pull and release the trigger to set the tool to the home position.
Removing the anvil (Fig. 1a)
• Loosen and remove retaining nut (D) and
remove anvil/nose housing from tool
• Using 24mm wrenches, unthread anvil (B)
from nose housing
• Reverse these steps to install anvil
Removing the Collet from tool (Fig. 2)
• Depress front clutch retaining tabs
• Fully unthread collet from pulling head adapter.
• To install collet, depress clutch retaining tabs and
thread collet all the way
NOTE: DO NOT USE WRENCHES TO TIGHTEN COLLET
D
B
C
A
3.2 NOSE
EQUIPMENT
NEW CONTENT BELOW THIS LINE
Prije upotrebe
• Postavite nosnu opremu odgovarajuće veličine.
• Provjerite je li baterija potpuno napunjena.
• Umetnite bateriju u alat.
• Brzo povucite i pustite okidač kako biste postavili alat u početni položaj.