Strong SRT 8222 User Manual

WARNING: The batteries should not be recharged, disassembled, electrically short-
circuited, be mixed or used with other types of batteries. If rechargeable
accumulators instead of batteries are going to be used, we recommend
using (e.g. NiMH) types with low self-discharge to ensure long time
operation of remote control.
1.5 Usage of external USB devices
 It is recommended to use USB 2.0 storage devices. If your device is not compatible to USB 2.0
specications, the playback with your receiver might not work properly.
 If you are going to use external USB HDD (Hard Disk Drive) please consider that the power
specications might exceed the supported output of your receiver (5 V/500 mA). If so, please
connect your USB HDD to an according external power adapter.
 STRONG cannot guarantee compatibility with all types of USB storage devices.
 It is advised not to store important information on USB storage devices used with the receiver.
Always make backups of data on your USB storage device before using it with this receiver.
STRONG will not take responsibility for any loss of information or circumstances caused by loss of
information.
 Please ensure that either the USB device is already formatted to NTFS or FAT32 or format the USB
device via your receiver. Formatting requires entering the PIN code (default 1234)
 STRONG cannot guarantee the playback of all les although extensions are listed, as it depends on
le size, codec, bit rate and resolution.
2.0 YOUR RECEIVER
2.1 PIN-CODE DEFAULT: 1234
2.2 Front Panel
Fig.1
1. Power button: Switch the receiver to Standby or On.
2. CH-/CH+: To change channels without using the remote control
3. LED Display Shows channel number and time in standby
4. Mode indicator: RED indicates that the receiver is in STAND-BY mode.
GREEN indicates that the receiver is in OPERATING mode.
5. IR sensor: Point your remote control towards this sensor.
6. USB: Connector for USB devices.
2.3 Rear Panel
Fig.2
1. RF IN To connect to your antenna for the reception of broadcast signal.
2. TO TV Loop-through antenna signal for another TV
3. S/PDIF Coaxial To connect your receiver to a digital audio amplier.
4. HDMI To connect your receiver with your TV set using a HDMI cable.
5. LAN To connect your receiver to Ethernet LAN
5

Strong SRT 8222 Specifications

General

Aspect ratio	16:9
Signal source	Terrestrial
Video resolutions	704 x 576, 720 x 576, 848 x 720, 1080 x 720, 1280 x 720, 1440 x 1080, 1920 x 1080 pixels
Supported video modes	576i, 576p, 720p, 1080i, 1080p
Digital signal format system	DVB-T2
Personal Video Recorder (PVR) included	-
Audio formats supported	AC3, MP3, PCM
Image formats supported	BMP, JPG
Video formats supported	H.264, H.265, MPEG2, MPEG4
Wi-Fi	No
Ethernet LAN	Yes
USB 2.0 ports quantity	1
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	0
Tuner type	Digital
Product color	Black
Audio decoders	Dolby Digital, Dolby Digital Plus
Number of tuners	1 tuner(s)
Channels quantity	400 channels
Audio output channels	- channels
Screen format adjustments	4:3, 16:9
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	1 W
Power consumption (typical)	10 W
Storage temperature (T-T)	-25 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 85 %
Display type	LCD

Weight and Dimensions

Depth	105 mm
Width	170 mm
Height	40 mm
Weight	270 g