EasyManuals Logo

Technics RS-TR575M2 User Manual

Technics RS-TR575M2
20 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #11 background imageLoading...
Page #11 background image
REVERSE
MODE
n
n
n
n
u
u
.u
u
dB
-SO
-15
-
n
i
;C:
Uul
”»
-3
000
ATC
n
n
n
n
u
u
.u
UGDio
n
u
dfl
-20
—)5
-10
—6
-3
030
*2
|>
ft
Recording
Types
of
tapes
which
can
be
used
for
recording:
NORMAL
POSITION/TYPE
I
p.
HIGH
POSITION/TYPE
H
p
METAL
POSITIONm'PE
IV
o
This
unit
is
equipped
with
an
ATC
function
page
14)
which
automatically
sets
the
optimum
recording
conditions
to
match
the
characteristics
of
the
tape
being
used.
It
is
recommended
that
you
use
this
function
when
recording.
Preparation
|
Wind
the
tape
past
the
leader
tape
section
so
that
recording
can
begin
straight
away.
The
procedures
described
below
are
an
example
of
recording
on
DECK
1.
Press
OPEN/CLOSE]
and
insert
the
cas¬
sette
tape
to
be
used
for
recording.
Press
again
to
close
the
cassette
holder.
Press
[DOLBY
NR]
to
select
the
appropriate
noise-reduction
system.
Each
time
the
button
is
pressed,
the
indicator
wiil
change
in
the
order:
\q\
\c\
—*
off.
t_i
Page
14.)
Press
[REVERSE
MODE]
to
select
desired
reverse
mode.
Each
time
the
button
is
pressed,
the
indicator
will
change
in
the
order:
CO.
t
i
-—
:
One
side
only
is
recorded.
'
OO
:
First
the
forward
side,
then
the
reverse
side
is
recorded.
Press
[ATC].
ATC
page
14)
takes
approximately
one
minute.
On
completion,
the
tape
returns
to
the
position
ATC
began
and
the
unit
stops.
The
“M”
indicator
shows
ATC
has
been
set.
[Recording
can
be
done
without
ATC.]
E3
Press
[•
REC].
(The
unit
will
be
in
the
recording
standby
mode.)
0
Play
the
source
in
order
to
adjust
the
record¬
ing
sound.
(Continued
on
next
page)
11
Recording

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Technics RS-TR575M2 and is the answer not in the manual?

Technics RS-TR575M2 Specifications

Audio Specifications IconAudio Specifications
signal-to-noise ratio (NR off)56 dB (A weighted)
signal-to-noise ratio (Dolby B NR on)66 dB (A weighted)
signal-to-noise ratio (Dolby C NR on)74 dB (A weighted)
Electrical Specifications IconElectrical Specifications
bias frequency80 kHz
input sensitivity and impedance100 mV/47 kΩ
output voltage and impedance500 mV/500 Ω
Power IconPower
power supply (UK, Australia, NZ)AC 230-240 V, 50/60 Hz
power supply (Others)AC 110 V/127 V/220 V/230-240 V, 50/60 Hz
power consumption (UK, Australia, NZ)28 W
Weight and Dimensions IconWeight and Dimensions
dimensions (W x H x D)430 x 136 x 285 mm
weight4.4 kg
tape speed4.8 cm/s

Related product manuals