EasyManuals Logo

Technics RS-TR575M2 User Manual

Technics RS-TR575M2
20 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #15 background imageLoading...
Page #15 background image
Recording
Tape-to-tape
recording
Use
DECK
2
to
record
the
sound
being
played
back
on
DECK
1.
1
Preparation
j
Wind
the
tape
past
the
leader
tape
section
so
that
recording
can
begin
straight
away.
Press
OPEN/CLOSE]
on
both
decks
and
insert
the
cassette
tapes.
DECK
1:
For
playback
DECK
2:
For
recording
Press
again
to
close
the
cassette
holder.
Press
[REVERSE
MODE]
to
select
the
desired
reverse
mode.
Each
time
the
button
is
pressed,
the
indicator
will
change
in
the
order:
,
*
cCD
OO.
•«—
:
One
side
only
is
recorded.
dt)
:
First
the
forward
side,
then
the
reverse
side
is
recorded.
The
playback
tape
is
played
up
to
eight
times
until
the
recording
tape
finishes.
CO
:
First
the
forward
side,
then
the
reverse
side
is
recorded.
CEE
To
record
on
only
one
side
of
the
tape,
set
the
tape
side
indi¬
cators
(<]
or
i>)
on
DECK
1
and
DECK
2
in
accordance
with
the
tape
sides
to
be
played
back
and
recorded.
To
record
on
both
sides
of
the
tape,
set
the
tape
side
indica¬
tors
on
both
DECK
1
and
DECK
2
to
the
forward
side
{[>).
Press
[SPEED]
to
select
a
recording
speed.
Each
time
the
button
is
pressed,
the
indicators
will
change
in
the
order:
x
i
jx~2j
off.
XI
:
Normal
speed
|~X2l
:
Double
speed
0
Press
[ATC]
on
DECK
2.
(The
ATC
function
will
enter
the
stand-by
mode.)
[Recording
is
also
possible
without
performing
ATC.)
0
Press
[SYNCHRO
START].
(ATC
will
begin,
and
when
it
is
completed,
recording
will
begin.)
To
stop
recording
Press
[
]
on
DECK
2.
Ifflffil
In
order
to
avoid
oper
ation
errors
later,
be
sure
to
switch
off
[SPEED]
(the
“XT
and
|
X2t
"
indicator
will
go
out)
after
the
tape-
to-tape
recording
has
fini
shed.
During
speed
recording
(
1
X21
)
,
the
unit
picks
up
interference
from
televisions
easier,
so
turn
the
television
off
or
separate
the
two
units.
75
Recording

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Technics RS-TR575M2 and is the answer not in the manual?

Technics RS-TR575M2 Specifications

Audio Specifications IconAudio Specifications
signal-to-noise ratio (NR off)56 dB (A weighted)
signal-to-noise ratio (Dolby B NR on)66 dB (A weighted)
signal-to-noise ratio (Dolby C NR on)74 dB (A weighted)
Electrical Specifications IconElectrical Specifications
bias frequency80 kHz
input sensitivity and impedance100 mV/47 kΩ
output voltage and impedance500 mV/500 Ω
Power IconPower
power supply (UK, Australia, NZ)AC 230-240 V, 50/60 Hz
power supply (Others)AC 110 V/127 V/220 V/230-240 V, 50/60 Hz
power consumption (UK, Australia, NZ)28 W
Weight and Dimensions IconWeight and Dimensions
dimensions (W x H x D)430 x 136 x 285 mm
weight4.4 kg
tape speed4.8 cm/s

Related product manuals