Need help?Do you have a question about the Tenda A18 and is the answer not in the manual?
General| Connectivity technology | Wired & Wireless |
|---|---|
| Ethernet LAN (RJ-45) ports | 1 |
| Ethernet LAN | Yes |
| Cabling technology | 10/100Base-T(X) |
| Networking standards | IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n |
| Ethernet LAN data rates | 10, 100 Mbit/s |
| Maximum data transfer rate | 867 Mbit/s |
| Supported data transfer rates | 11, 54, 300, 867 Mbps |
| Security algorithms | SSID, WPA-PSK, WPA-TKIP, WPA2-PSK |
| Product type | Network repeater |
| Product color | White |
| LED indicators | Power, Signal strength, WPS |
| DC input voltage | 9 V |
| Power source type | DC |
| Power consumption (max) | 5.2 W |
| Power consumption (typical) | 2.8 W |
| Frequency band | 2.412 - 2.484, 5.15 - 5.25 GHz |
| Channels quantity | 2 channels |
| Transmission gain | 12 - 16 dB |
| Receiver sensitivity | -97 dBm, -76 dBm, -74 dBm, -72 dBm, -95 dBm, -63 dBm |
| Antennas quantity | 2 |
| Antenna gain level (max) | 2 dBi |
| Storage temperature (T-T) | -40 - 70 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Storage relative humidity (H-H) | 5 - 90 % |
| Operating relative humidity (H-H) | 10 - 90 % |
| Flash memory | 8 MB |
| RAM capacity | 64 MB |
| Harmonized System (HS) code | 85176990 |
Weight and Dimensions| Dimensions (WxDxH) | 58 x 48 x 80 mm |
|---|
Lists the Tenda WiFi repeater models supported by this user guide.
Explains typographical conventions and symbols used throughout the manual for clarity.
Defines common acronyms and abbreviations used in the document for technical reference.
Provides links for more information and contact details for technical support assistance.
Provides an introduction to the WiFi repeater's capabilities, including coverage extension.
Highlights key features such as dual-band support, auto channel detection, and security mechanisms.
Explains the function of various LED indicators on the repeater for status monitoring.
Describes the physical ports and buttons on the repeater for connection and control.
Details the information found on the device labels, such as SSID and default access.
Explains the two operating modes and guides the user in selecting a setup scenario.
Provides step-by-step instructions for extending WiFi coverage using web UI or WPS methods.
Guides on configuring the repeater to function as an Access Point for wired-to-wireless conversion.
Details how to view internet connection status and signal strength across bands.
Lists connected devices with their names, connection types, and MAC addresses.
Explains how to block unauthorized devices and unblock previously restricted devices.
Provides steps to change the repeater's WiFi network name (SSID) and password.
Details the process of hiding the repeater's WiFi network SSID for improved security.
Explains the two primary operating modes: Repeater Mode and Access Point (AP) Mode.
Guides on switching the repeater from its default Repeater Mode to AP Mode.
Provides instructions to switch the repeater from AP Mode back to the standard Repeater Mode.
Instructions for changing the repeater's login password to enhance network security.
Covers procedures for rebooting the repeater and performing a factory reset.
Covers procedures for rebooting the repeater and performing a factory reset.
Explains how to export system logs and upgrade the repeater's firmware.
Explains how to export system logs and upgrade the repeater's firmware.
Step-by-step guide for configuring automatic IP address acquisition on Windows 7.
Lists default parameters such as login address, password, operating mode, and SSID.
To Next Page
