Textron JACOBSEN GP400

To Next Page

To Previous Page

8 MAINTENANCE & LUBRICATION

en-55

FLUID REQUIREMENTS

Quantity Type

A Engine Oil (with filter) 1.4 litres SAE30, SAE5W 30, 10W 30

B Hydraulic Oil (with filter) 22 litres GreensCare ISO VG 46

D Fuel 55 litres Lead Free Minimum 85 Octane

Main Page

Table of Contents2
Important3
Product Identification4
Guidelines for the Disposal of Scrap Products6
During Service Life6
End of Service Life6
Parts Manual7
Key Numbers8
Safety8
How to Operate Safely9
Safe Operation9
Preparation9
Operation10
Rops11
Safe Handling of Fuels11
Maintenance and Storage11
When You Put the Mower on a Trailer12
Important Safety Notes13
Specification16
Engine Specification16
Dimensions & Weights17
Machine Specification18
Vibration Level19
Noise Level20
Slopes20
Cutting Unit Specification21
Cutting Performance21
Recommended Lubricants22
Accessories22
Certificates of Conformity23
Notes27
Decals28
Safety Decals28
Instruction Decals30
Notes31
Controls32
Operator Workstation32
Instrument Panel33
Starter Key Switch34
Throttle Control Lever34
Cutting Unit Switch (PTO)34
Engine Coolant Temperature (Diesel Only)35
Working Lights35
Hour Meter35
Blocked Hydraulic Filter Warning Light36
Multifunction Warning Light36
Oil Pressure Warning Light36
Choke Control (Gasoline Only)36
Mow / Transport Lever37
Power Outlet37
Horn Button37
Parking Brake37
Traction Pedal38
Steering Wheel38
Lift & Lower Rate & Synchronisation Control38
Free Wheel39
Operation40
Daily Inspection40
Operator Presence and Safety Interlock System40
Operating Procedure41
Setting up the Machine43
Mounting the Cutting Heads44
Reel Motor Mounting45
Cutting Cylinder Lift & Lower Synchronisation46
Operation of the Machine46
Starting the Engine47
Driving47
Mowing Procedure47
To Stop the Engine48
How to Remove a Blockage from Cutting Units48
Backlapping49
Backlapping Procedure50
Transporting on a Trailer or Flatbed50
Slinging and Jacking the Machine50
Mowing on Slopes51
Slope Calculation Chart53
Maintenance and Lubrication54
Maintenance and Lubrication Chart54
Engine Lubrication - Gasoline54
Engine Lubrication - Diesel56
Engine Access58
Engine Oil Level - Gasoline58
Engine Oil Change- Gasoline59
Engine Oil Filter- Gasoline59
Air Filter - Gasoline60
Engine Fuel Filter - Gasoline61
Oil Cooler Gasoline Machine61
Air Filter - Diesel63
Engine: Fan Belt - Diesel63
Engine Coolant - Diesel64
Oil Cooler and Radiator - Diesel65
Bleeding the Fuel System - Diesel66
Air Cleaner - Diesel67
Battery - Gas & Diesel67
Hydraulic System - Gas & Diesel68
Handbrake - Gas & Diesel69
Tyres - Gas & Diesel69
Machine Maintenance General - Gas & Diesel70
Lubrication of Cutting Unit70
Notes71
Adjustments72
Traction Control Pedal72
Adjusting Speed Control Switch73
Steering Arm Adjustment73
Rear Swing out Arm74
Levelling Linkage for the Front Cutting Heads75
Seat Adjustment76
Bedknife-To-Reel Trueset™ Reel81
Bedknife Adjustment Trueset™ Reel82
Cutting Height Trueset™ Reel83
Reel Beartrueset™ Reel84
Bedknife Adjuster Spring Trueset™ Reel84
Bedknife Adjuster Tension Trueset™ Reel85
Grinding Bedknife Trueset™ Reel85
Bedknife Adjustment Classic Xp™ Reels86
Height of Cut Classic Xp™ Reels87
Accessories88
Three Wheel Drive Kit88
Paddle Kit88
Dew Whip Kit89
Groomer Kit89
Notes90
Problem Solving91
Problem Solving General91
Quality of Cut92
Quality of Cut Troubleshooting92
Washboarding92
Marcelling93
Step Cutting94
Scalping95
Stragglers96
Streaks97
Windrowing98
Rifling or Tramlining99
Matched Cutting Units99
FUSES and RELAYS Fuse and Relay Identification101
Notes102
Guarantee103
Warranty103
Service103
Evaporative Emission Control Warranty Statement104

Textron JACOBSEN GP400 - Page 55

Table of Contents

Other manuals for Textron JACOBSEN GP400

Related product manuals