ENGLISH
ENGLISH
11
ELECTRELECTR
ELECTRELECTR
ELECTR
ONIC ONIC
ONIC ONIC
ONIC
TT
TT
T
AA
AA
A
CHOMETER (END/SMR/SMM)CHOMETER (END/SMR/SMM)
CHOMETER (END/SMR/SMM)CHOMETER (END/SMR/SMM)
CHOMETER (END/SMR/SMM)
The electronic tachometer display is always activated.
The electronic tachometer is powered by an SR44 1.5 Volt battery,
(D357) 11.6x5.4mm.
Replace the battery every 2 years or in case of blurring of the display.
To replace the battery, open the cover positioned on the rear using a
screwdriver, and extract the battery.
Insert the new battery in a way that the positive pole is visible from the
outside and close the cover.
Before extracting the battery, make note of the WS (wheel circumference)
and DST (total mileage) values.
These values will be re-programmed into the instrument after battery
replacement.
MODE SELECTION AND RESETMODE SELECTION AND RESET
MODE SELECTION AND RESETMODE SELECTION AND RESET
MODE SELECTION AND RESET
(END/SMR/SMM)(END/SMR/SMM)
(END/SMR/SMM)(END/SMR/SMM)
(END/SMR/SMM)
While the electronic tachometer always displays the speed of the vehicle
expressed in Kmh (or Mph on the basis of the selection made) it also
allows to visualise the following functions on selection:
TRP Daily mileage
AVS Average speed (after 10 hours or 1000Km press RESET)
STP Chronometer (start and stop autom. max. time 10 hours)
MAX Max. speed reached (from the last RESET)
DST Total mileage (up to 99999Km)
CLK Clock
To reset theTRP, AVS, STP and MAX functions, press the right button (blue).
Select the function and press the left button for 5 sec. (yellow).
The values displayed are zeroed.
PP
PP
P
RR
RR
R
OGRAMMING OGRAMMING
OGRAMMING OGRAMMING
OGRAMMING
THE ELECTRTHE ELECTR
THE ELECTRTHE ELECTR
THE ELECTR
ONIC ONIC
ONIC ONIC
ONIC
TT
TT
T
AA
AA
A
CHOMETERCHOMETER
CHOMETERCHOMETER
CHOMETER
(END/SMR/SMM) (END/SMR/SMM)
(END/SMR/SMM) (END/SMR/SMM)
(END/SMR/SMM) (only after battery replacement)
Remove the connector positioned on the back of the instrument.
Press the grey button on the rear of the instrument for 5 seconds. Four
numbers appear on the display, of which the first is flashing. “WS”
(Wheel Size) also flashing, appears in the top right of the display.
Now press in sequence, the left hand button (yellow) to change the
value of the first flashing number.
Press the right hand button (blue) to make the second number flash
and press the left hand (yellow) button in sequence to visualise the
desired value.
Repeat the operation to change the value of the following number and
so on until the exact development of the wheel expressed in mm. (=tyre
diam. in mm.x3.14) is visualised.
Finally, with the 4th number still flashing, to change the unit of
measurement from Kmh to Mph, press the right hand button (blue)
and “Kmh” will start to flash,now press the left hand button (yellow) to
pass to “Mph”.
End programming by pressing the grey button on the rear of the
instrument for 1 sec.
OPERAOPERA
OPERAOPERA
OPERA
TING CONTRTING CONTR
TING CONTRTING CONTR
TING CONTR
OLSOLS
OLSOLS
OLS
OPERAOPERA
OPERAOPERA
OPERA
TING CONTRTING CONTR
TING CONTRTING CONTR
TING CONTR
OLSOLS
OLSOLS
OLS
To Next Page
Loading...
Need help?
General
