Toro 30873TE - Accessing the Hydraulic Lift Compartment; Lubrication; Greasing the Bearings and Bushings

72 pages

To Next Page

To Previous Page

AccessingtheHydraulic

LiftCompartment

Tilttheseattoaccessthehydraulicliftcompartment

asshowninFigure34.

g036706

Figure34

Lubrication

GreasingtheBearingsand

Bushings

ServiceInterval:Every50hours(alsoafterevery

washing).

Greasespecication:No.2lithiumgrease

Thegreasettinglocationsandquantitiesareas

follows:

•Brake-shaftpivotbearings(5)asshowninFigure

g009704

Figure35

•Rear-axle-pivotbushings(2)asshowninFigure

36)

g009705

Figure36

Main Page

Table of Contents3
Safety4
General Safety4
Engine Emission Certification4
Safety and Instructional Decals5
Setup12
Installing the Decals (CE Machines Only)12
Installing the Hood Latch13
Adjusting the Roller Scraper14
Installing the Mulching Baffle14
Preparing the Machine15
Product Overview16
Controls16
Specifications23
Machine Specifications24
Cutting Unit Specifications24
Attachments/Accessories24
Before Operation25
Before Operation Safety25
Checking the Engine-Oil Level25
Checking the Cooling System25
Checking the Hydraulic System25
Draining the Water Separator25
Checking the Rear Axle and Gearbox for Leaks25
Filling the Fuel Tank25
Checking the Tire Pressure27
Checking the Torque of the Wheel Lug Nuts27
Adjusting the Height of Cut27
Checking the Interlock Switches28
Checking the Blade-Stopping Time28
Selecting a Blade29
Choosing Accessories30
During Operation30
During Operation Safety30
Starting the Engine32
Shutting off the Engine32
Understanding the Operating Characteristics of the Machine32
Operating the Engine-Cooling Fan32
Using Cruise Control33
Using the Transport Latches33
Operating Tips34
After Operation35
General Safety35
Using the Cutting-Unit Storage Lanyard35
Hauling the Machine36
Pushing or Towing the Machine36
Locating the Tie-Down Points37
Maintenance38
Maintenance Safety38
Recommended Maintenance Schedule(S)38
Daily Maintenance Checklist39
Pre-Maintenance Procedures41
Lifting the Machine41
Opening the Hood41
Accessing the Hydraulic Lift Compartment42
Lubrication42
Greasing the Bearings and Bushings42
Engine Maintenance44
Engine Safety44
Servicing the Air Cleaner44
Servicing the Engine Oil45
Fuel System Maintenance46
Draining the Fuel Tank46
Inspecting the Fuel Lines and Connections46
Servicing the Fuel-Water Separator47
Servicing the Fuel Filter48
Cleaning the Fuel-Pickup Tube Screen48
Priming the Fuel System49
Electrical System Maintenance49
Electrical System Safety49
Checking the Battery Condition49
Charging and Connecting the Battery49
Locating the Fuses51
Drive System Maintenance52
Checking for End-Play in the Planetary Drives52
Checking the Planetary Gear-Drive Lubricant52
Changing the Planetary-Gear-Drive Oil53
Checking the Rear Axle and Gearbox for Leaks54
Checking the Rear-Axle Lubricant54
Changing the Rear-Axle Lubricant55
Checking the Rear-Axle-Gearbox Lubricant55
Checking the Rear Wheel Toe-In55
Cooling System Maintenance56
Cooling System Safety56
Checking the Cooling System56
Cleaning the Cooling System57
Brake Maintenance58
Adjusting the Service Brakes58
Belt Maintenance59
Servicing the Alternator Belt59
Hydraulic System Maintenance59
Hydraulic System Safety59
Servicing the Hydraulic Fluid60
Checking the Hydraulic Lines and Hoses63
Cutting Unit Maintenance63
Removing the Cutting Units63
Installing the Cutting Units64
Servicing the Front Roller64
Blade Maintenance65
Blade Safety65
Servicing the Blade Plane65
Removing and Installing the Cutting-Unit Blade(S)66

Other manuals for Toro 30873TE

Installation Instructions8 pages

Related product manuals

Toro Groundsmaster 3500 30807

283 pages

Toro 30868 Groundsmaster 4700-D

52 pages

Toro 30856 Groundsmaster 4500-D

48 pages

Toro 30609

374 pages

Toro 30873TE - Accessing the Hydraulic Lift Compartment; Lubrication; Greasing the Bearings and Bushings

Table of Contents

Other manuals for Toro 30873TE

Related product manuals