Toro 38682 - User Manual

Questions and Answers

A
Amber DavisAug 8, 2025
How to fix uneven cutting height on Toro 38682?
- M
  Matthew SerranoAug 8, 2025
  If you notice an uneven cutting height with your Toro Lawn Mower, here are a few things to check: * The blade(s) may not be sharp; sharpen the blade(s). * The cutting blade(s) may be bent; install new cutting blade(s). * The mower may not be level; level the mower from side-to-side and front-to-rear. * The underside of the mower may be dirty; clean the underside of the mower. * The tire pressure may not be correct; adjust the tire pressure. * The blade spindle may be bent; contact an Authorized Service Dealer.
G
Gabrielle SandersAug 12, 2025
What to do if Toro 38682 blades do not rotate?
- B
  Barbara BarajasAug 13, 2025
  If the blades on your Toro Lawn Mower do not rotate, consider these possible causes: * The mower deck belt may be worn or loose; check the belt tension. * The mower deck belt may be broken; install a new deck belt. * The mower deck belt may be off the pulley; inspect the belt and replace it if damaged, then check the pulleys and idlers and adjust the belt tension. * There may be a broken or missing idler spring; replace the spring.
J
jhullAug 16, 2025
Why does my Toro 38682 engine overheat?
- H
  Hunter LopezAug 16, 2025
  Your Toro Lawn Mower engine may overheat due to these reasons: * The engine load is excessive; reduce the ground speed. * The oil level in the crankcase is low; add oil to the crankcase. * Cooling fins and air passages under the engine blower housing are plugged; remove the obstruction from the cooling fins and air passages.
P
pdanielsAug 21, 2025
What causes abnormal vibration in Toro Lawn Mower?
- J
  Jason MillerAug 21, 2025
  Abnormal vibration in your Toro Lawn Mower can be attributed to several factors: * The cutting blade(s) may be bent or unbalanced; install new cutting blade(s). * The blade mounting bolt may be loose; tighten the blade mounting bolt. * The engine mounting bolts may be loose; tighten the engine mounting bolts. * A loose engine pulley, idler pulley, or blade pulley; tighten the appropriate pulley. * The engine pulley may be damaged; contact an Authorized Service Dealer. * The blade spindle may be bent; contact an Authorized Service Dealer.
S
smithchristineAug 26, 2025
Why Toro 38682 Lawn Mower machine does not drive?
- G
  gmitchellAug 26, 2025
  If your Toro Lawn Mower machine does not drive, consider the following: * The shift lever may be in neutral; move the shift lever to a drive gear position. * The traction belt may be worn, loose, or broken; change the belt. * The traction belt may be off a pulley; change the belt. * There may be a broken or missing idler spring; replace the spring.
C
Charles AllenOct 30, 2025
Why Toro 38682 Lawn Mower engine will not start?
- B
  Brandon CarterOct 30, 2025
  If your Toro Lawn Mower engine won't start, starts hard, or fails to keep running, there are several potential causes: * The fuel tank may be empty; if so, fill the fuel tank with gasoline. * The fuel shut off valve may be closed; in this case, open the fuel shut off valve. * The choke may not be on; move the throttle lever to the choke position. * The air cleaner may be dirty; clean or replace the air cleaner element. * The spark plug wire may be loose or disconnected; install the wire on the spark plug. * The spark plug may be pitted, fouled, or have an incorrect gap; install a new, correctly gapped spark plug. * There might be dirt in the fuel filter; replace the fuel filter. * There could be dirt, water, or stale fuel in the fuel system; in this situation, contact an A...
R
rachel18Nov 3, 2025
What to do if Toro 38682 engine loses power?
- V
  vbyrdNov 3, 2025
  If your Toro Lawn Mower engine loses power, here's what you can check: * The engine load may be excessive; reduce the ground speed. * The air cleaner may be dirty; clean the air cleaner element. * The oil level in the crankcase may be low; add oil to the crankcase. * Cooling fins and air passages under the engine blower housing may be plugged; remove the obstruction from the cooling fins and air passages. * The spark plug may be pitted, fouled, or have an incorrect gap; install a new, correctly gapped spark plug. * The vent hole in the fuel cap may be plugged; clean or replace the fuel cap. * There might be dirt in the fuel filter; replace the fuel filter. * There could be dirt, water, or stale fuel in the fuel system; in this situation, contact an Authorized Service Deale...