Connecting a VCR and sateJJitereceiver
Note: The TVGuide On Screen _system does not receive program
I/st177gsfron? or for arty satellite serwce
You will need:
_, three coaxial cables
_, one se[ ef cemper_er_t video cables (ifyour
sateIIite receiver dees r_e[ have cernpor_en[
vide(), cotmec[ d_e standard A/V cables only)
d_ree sets efs[andard A/V cables
• f%rbette/picture peffonrlanc< ifyoln satellite
receiverand VCRhaveS video connectS vkleo
cables(_olustheaudio cr;,b/e._2inste_dof thestan@rd
videocables Do not connectboth_/pe,_of video
cablei?)VIDEO 1(or I/IDEO2) atthesamef/?rleor
thepictureperformancewinbe unacc'eptabb
• ffyou havea mono I/CA c-or?f?ectZ/MONO on the
T1/(VIDEO 0 _)your VCR_AUDIO OUTj_c'kusi/w
the whiteauogbcab/eon/_
C3
To view satellite programs using the
component video connections:
Sdec[ the ColerS[ream HD-! video input
source on the TV.*
To view satellite programs using the standard
From
antenna
From
satellite
dish m
C3
video connections or to record satellite programs:
T, rr_on aHthree de_ices. SeEd_e VCR to the appropriate
lirle irlpttt (refer te your.VCR owner's manual tbr details).
Sdect the VIDEO 2 video input source on the TV.*
To view the VCR or view and record antenna channels:
Turn ON the VCR. Sdec[ the ANT-! video input source
on the TV.*
Tune the TV to cham_d 3 or 4 (whichever cham_d isvacant
in your area).
T, rn ON the VCR. Ttme d_eVCR [o the channel yeu
war_tto watch. Sdect the VIDEO 1 _ideo input source on
d_eTV.*
* ]o select the video input source, press IN PUT on the remote control
(see page 67). ]o program the TV remote control to operate other
devices, see Chapter 3,
The mmuthorized recording, use, distribution, or revision of television
programs, videotapes, DVDs, and other raateriaJs is pmhihRed under the
Copyright Laws of the United States and other countries, and may sabiect
you to civil and criminal liability.
StereoVCR
Satellite receiver
Note: The VIDEO!AUDIO OUTjac£s ou@ut the s/)'na£ from the
ANT 7,ANT2, I/IDEO L VIDEO 2, or VIDEO 3/?_ckswhen the
appropr_?_teinput mode £ selected
To use the TV Guide On Screen recording features:
1. Connect the G-LINK cable according to the insmtcdons
on page 25.
2. Make sure the VCR is connected to the A/V OUT jacks
on the TV (see illus[radon).
3. Se[ the VCR to the apprepriate line input (retbr to >ur
VCR owner's manual for de[ails), and then mrn OFF the
VCR.
4. See Chap[er 5 for details on setting up the TV Guide
On Screen system.
5. See Chapter 7 [br de_ailson using the TV Guide
On Screen system.
÷
H94(E)012-25(2B-Cnct)
15
Copyright @ 2004 TOSHIBA CORPOFtATION, All rights reserved,
÷
813/04, 3:41 PM
15
r
To Next Page
Loading...
