Toshiba 51H94 - Programmingthe Remote Control to Operate Yourother Devices; Device Code Setup

A ÷ [
Programmingthe remote control to operate yourother devices
Device code setup
1_ Refer to the muIti-brand remote contro_ device code table
on pages 32-33 to find the code for the brand of'yottr
device.
If'more than one code is listed, try each one separatdy until
3xmfind the one that works.
2. Press MODE mlfiI the Mode indicator fbr the device
(CBL/SAT, VCR/PVR, DVD, AUDIO 1, AUDIO 2)
lights up.
3. While holding down the RECALL bumm, press the
Channel Number buttons to enter d_efbur-digit code fbr
your brand of'device. If'a valid code is entered, the mode
indicator will blink twice. If' an invalid code is entered, she
mode indicator will blink one long blink.
4. Point the remote control at the device and press POWER to
test the code.
ff'&edevice l*'sf,ovds> &e l_','_ow_,wol:
You have entered the correct code.
ff'&e devicedoeyJ_otre_j.,ovdh &e re,,_olecomrol:
You may have entered the wrong code. Repeat steps 3
and 4 using another code.
Note: Ir_addition to POWER, coslfhz71that aNnecessa/y keys
of7the TVf_fTsotecrJp_/olopel_#e you[ clevice ff some keys
are not opei_@)na/, repeat the device code setup _lsiiW
8fsothe/ code (if otlse/ codes 8re Shred for you/ devicej
St,afte/ tfyieg all I/sted codes, the necessa/y keys do slot
oper_m your dev/ce, t_serise dev/ce_ of_4//?altemote cont/o/
5. Press MODE to select the TV mode to control the TV.
Note:
• /although the TV_emote coRtlol includes codes _)f masly device& it may
not bclude codes for some or all of the features on certain clev/cesyou
wish to controL Ifyou are unable to progr_sm the TV femote cofFf_)/to
operate you/device o_ some of the features on that o'ev/ce, use the
device's fwrJote control or the cosltmh oslthe device
• _)schthTleyoudsailgetheba_eriesyouw///needtoreprog/_mthe
remote cosfffoZ
• Some fsewe/VORs [espofsd tOe/the/of two codes These VCR_ have a
sw/lch bbe/ed "VCRWVCR2" ff your VCRhas this kind of switch and
does not _espond to tile codes for VotJ/ VCP,bmncZ set the switch to _?se
other posiUon ("VCR 7"or "VC?R2') and teptogm£rl tile tWTsoteco/st[oL
Searching and sampling the code
of a device (8500)
If'you do riot know the device code f'ora particular device, you
can cycIe the remote controI through the avaiIabIecodes for that
device mode and sample the f'mlctions to find the code that
operates the target device. The keys avaihbIe to be sampled,
provided they are applicable to that mode, are POWER, 1,
VOL &, CH &, and PLAY.Invalid keys will be ignored while in
program mode.
To cycle through each available device code and sample its
_nctions:
1.
2.
Press MODE to select the mode you want to set up.
WhiIe biding down RECALL, press 8 - 5 - 0 - 0.
The remote control will enter program mode.
Point the remote control at the target device and press
POWER (or other f'ttnction buttons that are available to be
sampled).
/TiDe device respowts> &e re,,_otec0mr0L'
Press RECALL to store the device code. The mode
indicator will blink twice and the remote control will exit
the program mode.
ff'&edevicedoess_otres?ond > &e rev_olecovtrol:
Press A, arid then press POWER.
Repeat this step until the device responds co the remote
control, and then press RECALL.
Note: When a seamh cycle h comphter/, the mode
/ndk;ak)r v/ill b/ink throe times. The remote oontto/ wi//
begin Io r:yc/e Usmugh the avai/ab/e codes again, if no key
is pressed wilhin 10 seconr/s whi/e pmgmmmi/?g, ffse
remote cotstsT/ will exit he program mode and return to file
pmvsbus corse.
-- POWER
-- Numbers
MODE
EA
--VOL A/_
i RECALL
÷
30
H94(E)026-," (3-RC)
3O
Copyright @ 2004 TOSHIBA CORPORAEION. All rights reserved.
÷
813/04, 3:55 PM
[