A ÷ L
Setting up and using TheaterNef" on-screen device control
The TheaterNet fbature allows you to control many brands of"
IEEE-1394 and/or infrared rernote<ontrolDd A/V devices
through your TV using on-screen control icons and the TV's
remote control
Note:
• Ah'hol_qh the777eaterNetonscreendevke c:ontmlfem'uzeincludes
codesformanycleviees,it maynotincludecod_sforsomeoraNof
therestatesonoert;dndeviees you wishtoCOfTtfeLIf J/eLI am unable
toprogramriteTheate/Netteature17>operate yourdeviceofso177eof
thefeatulesonthatdevice, use thedevice_remotecontlo/of the
COfTtfel!_ Of7 the device
• For IR pass thmt\qh device control bfo/mation, see "('onnecting
kFmmd remote cofTtlo//ed (Jel/ioes to the/R OUT[/Jol<" Oll page 2 7
Setting up TheaterNet
AII de, ice types except IEEE-1394 require the fblh)wing seRtp
process befbre you can contro_ them using the TheaterNet
on-screen icons.
AH CompatibD IEEE-1394 devices are atnomaticaIIy recognized
by the TheaterNeE fbature and do not require setup.
Note: .Seepnge 22 for det_dsaboutthe IFEF 1394per> Ifyod_
/EEE 1394deviceisfTotrecognizedthrough theIEEF 1384po£ or
ffTletJ_h {he 7heaterNetfentu/_,it maybe possibleto set ituptot IR
passt/IrotLq/Icontrolas atlhTf/_lreddevice(seepage20
To set up TheaterNet device control:
1. Make sure you have properly connected your infrared
remote-controlled device(s). See page 21 for details.
2. Press MENU and open the SETUP menm
3. Highlight INSTALLATION and press ENTER. (A new set
of INSTALLATION menu icons will appear on-screen, as
shown in step 4).
_&N_vlgate _Select _BacR _*ii_E×it
Open the DEVICES menu, highlight THEATER NET
DEVICES, and then press ENTER.
_Navigate _Se]ect _._gack _:_Exit
The TheaterNeE Setup menu opens.
5. Using the _t _ buttons, sdect the INPUT the device is
connected to.
Note: l/¢ker_the input/s change< all unsaved settings
_vi/Ibe lost
6. Press _ and then *__ to sdect the device TYPE.
7. Press _' and then @_ to sdecr the device BRAND
Note: Whorl selecting a/low brand, the IR code will/)e set
I_) 7ere
8. Press _' and then *__ to sdect the device's IR code.
9. If the desired IR code is found, skip to step 10.
If the desired IR code is not in the list, press _ and use the
ChamM Number buttons to enter the device IR code.
Note: _)u can find tile IR code _)r you/ device in the
oil sc/_en list or k7the 2?eaten\let device ooo'e t_bb of 7
pages 4U 48
10, Highlight TEST and press ENTER to test whether the
device responds to the code.
If"the device does not respond to the code, repeat steps
8 and 9 using another code for the same device.
11. When done, highlight SAVE and press ENTER.
To remove a device from TheaerNet:
1, Follow steps 1-5 above.
2. Highlight RESET and press ENTER.
3. Highlight SAVE and press ENTER.
÷
H94(E)044-. _
44
-P(6b-Setup)
44
Copyright @ 2004 TOSHIBA CORPORA]ION. All rights reserved.
÷
813/04, 5:27 PM
[
To Next Page
Loading...
