Why is the printed image from my Toshiba B-EX4T1 Barcode Reader blurred?
If the printed image from your Toshiba Barcode Reader is blurred, it could be because the combination of ribbon and media is not proper, or the Print Head is not clean. Select an appropriate ribbon for the media type being used. Clean the print head using the Print Head Cleaner or a cotton swab slightly moistened with ethyl alcohol.
What to do if my Toshiba B-EX4T1 Barcode Reader displays 'Head Open'?
If your Toshiba Barcode Reader shows 'HEAD OPEN', it means that feeding or printing has been attempted with the Print Head Block open. Close the Print Head Block and then press the [RESTART] key.
Why is my Toshiba Barcode Reader printing nothing on the media?
If your Toshiba Barcode Reader is not printing anything on the media, it could be due to several reasons. The media or ribbon might not be loaded properly, the print head might not be installed correctly, or the combination of ribbon and media might not be suitable. Ensure the media and ribbon are loaded properly, the print head is correctly installed and the Print Head Block is closed, and select an appropriate ribbon for the media type being used.
What to do if my Toshiba B-EX4T1 Barcode Reader shows 'Cutter Error'?
If your Toshiba Barcode Reader displays a 'CUTTER ERROR', especially if the cutter module is installed, it could be due to the media being jammed in the cutter or the cutter cover not being attached properly. Remove any jammed media and ensure the cutter cover is properly attached. Then, press the [RESTART] key. If the problem persists, turn off the printer and contact a TOSHIBA TEC authorised service representative.
Why won't my Toshiba Barcode Reader turn on?
If your Toshiba Barcode Reader will not turn on, there are a few potential causes. First, ensure the power cord is properly plugged in. If it is, test the AC outlet with another electrical appliance to confirm it's functioning correctly. Finally, check the fuse or circuit breaker to see if it has blown or tripped.
How to resolve a 'Comms Error' on my Toshiba B-EX4T1?
If your Toshiba Barcode Reader displays a 'COMMS ERROR', a communication error has occurred. Ensure the interface cable is correctly connected to both the printer and the host, and verify that the host is turned on.
How to fix 'No Paper' error on Toshiba Barcode Reader?
If your Toshiba Barcode Reader shows a 'NO PAPER' error, it could be due to several reasons: the media may have run out, is not loaded properly, the sensor position is not adjusted properly, the media sensor hasn't been properly calibrated, or the media is slack. To resolve this, load new media or reload the media correctly. Adjust the sensor position and take up any slack in the media. After performing any of these corrections, press the [RESTART] key. If the media sensor hasn't been properly calibrated, refer to Section 2.10 to set the threshold or call a TOSHIBA TEC authorised service representative.
What does 'Syntax Error' mean on my Toshiba B-EX4T1?
If your Toshiba Barcode Reader displays 'SYNTAX ERROR', it indicates that while the printer is in the Download mode for upgrading the firmware, it receives an improper command. Turn the printer off, and then on again.
What causes a 'Ribbon Error' on a Toshiba B-EX4T1?
A 'RIBBON ERROR' on your Toshiba Barcode Reader can occur if the ribbon is not fed or loaded properly, or if the ribbon sensor has a problem. Remove the ribbon and check its status, replacing it if necessary. If the problem persists, turn off the printer and contact a TOSHIBA TEC authorised service representative.
What should I do if my Toshiba B-EX4T1 Barcode Reader says 'No Ribbon'?
If your Toshiba Barcode Reader displays a 'NO RIBBON' error, it means the ribbon has run out. Load a new ribbon and then press the [RESTART] key.
General| Print Method | Thermal Transfer / Direct Thermal |
|---|---|
| Type | Industrial Barcode Printer |
| Operating Temperature | 5°C to 40°C |
| Resolution | 203 dpi |
| Print Width | 104 mm |
| Interfaces | USB, Ethernet |
| Optional Interfaces | Wireless LAN, Bluetooth |
| Supported Barcodes | UPC/EAN, Code 39, Code 93, Code 128, ITF, NW-7 |
| Storage Temperature | -20°C to 60°C |
| Humidity | 25% to 85% non-condensing |
Provides an introduction to the TOSHIBA B-EX4T1 series barcode printer and its manual.
Details the printer's features and the unpacking process, including notes on inspection.
Describes the printer's physical appearance, including dimensions and views of its parts.
Lists and describes various optional kits and modules available for the printer.
Covers printer installation, safety precautions, power cord connection, and cable setup.
Provides detailed steps for loading various types of media and ribbons into the printer.
Explains how to turn the printer on/off and navigate printer settings via the operation panel.
Details various advanced settings including LAN/WLAN, BASIC, Z-Mode, calibration, logging, etc.
Guides users through the process of installing printer drivers on different Windows versions.
Covers performing print tests and fine-tuning print position, tone, and sensor settings.
Explains the functions of the operation panel keys and the LCD display information.
Illustrates common printer operations and responses to events like errors or pauses.
Provides detailed instructions for cleaning the print head, platen, sensors, covers, and cutter.
Lists common error messages, their probable causes, and initial troubleshooting steps.
Addresses potential problems like no print, blurred image, cutter issues, and media jams.
Details physical, power, resolution, and printing speed specifications for the printer models.
Lists supported barcode types, fonts, rotations, and interface options.
Describes media types, dimensions, detection areas, RFID tag usage, and cautions.
Details ribbon specifications, recommended media/ribbon types, and care instructions.
Provides a comprehensive list of LCD messages and their corresponding LED indications.
Details USB, LAN, Serial, Parallel, Expansion I/O, Wireless LAN, and RFID interfaces.
Illustrates various font styles and barcode types supported by the printer.
Defines key terms and concepts related to the printer's operation and features.
To Next Page