To Next PageTo Next Page
Need help?Do you have a question about the Trane GEHE and is the answer not in the manual?
Details types of warnings, cautions, notices, and general safety advice.
Highlights critical safety warnings for electrical, PPE, and equipment hazards.
Explains the coding system for GEH/GEV unit model numbers by digit.
Details the coding system for EXH/EXV unit model numbers by digit.
Describes the manual's purpose, and details on unit and compressor nameplates.
Explains how model numbers identify unit type, operation, and components.
Details unit construction, including coils and control system options.
Describes available control options: Basic 24V, Deluxe 24V, Tracer ZN510, and ZN524.
Explains the need for thermostats or BAS for unit operation.
Covers optional features like waterside economizers, electric heat, and hot gas reheat.
Checklists for inspecting units for damage and verifying jobsite readiness.
Guidelines for storing units to prevent damage and microbial growth.
Specifies required clearances for service access for GEH and EXH models.
Details required service clearances for GEV and EXV models across various sizes.
Presents dimensional data for GEH/EXH units based on airflow configurations.
Specifies dimensional data for GEV units based on airflow configurations.
Presents dimensional data for GEH/EXH units with waterside economizer.
Provides dimensions for GEV units with waterside economizer.
Lists net and shipping weights for GEH, GEV, EXH, and EXV units.
Illustrates weight distribution for hanging GEH and EXH units for proper installation.
Provides a checklist for essential steps to ensure successful unit installation.
Covers main power, electric heat, low voltage wiring, and grounding requirements.
Describes filter types and installation requirements, noting factory-installed filters.
Instructions for supply-air, return-air ductwork, and ducted panels.
Steps for installing a dual filtration system for improved air quality.
Guidance on condensate drain traps and supply/return pipe connections with flexible hoses.
Procedure for cleaning the water loop and using balancing kits for flow control.
Step-by-step guide for installing the waterside economizer on GEH/EXH units.
Procedure for installing the waterside economizer on GEV units.
Instructions for wiring the economizer control board, sensors, and valves.
Guidance on insulating economizer piping and installing a condensate trap.
Table listing part numbers for Trane economizer accessories.
Steps for starting up the economizer, including thermostat settings and refrigerant checks.
Table detailing specifications for waterside economizing three-way valves.
Table listing electrical data for standard static motor configurations.
Provides electrical data for high static motor configurations.
Lists electrical data for ECM motor configurations.
Table summarizing minimum and maximum electrical values for various units.
Comprehensive checklist of system devices to verify before unit energization.
Step-by-step guide for the initial start-up of the heat pump unit.
A checklist for contractors to verify system checks and log data before operation.
Explains variables affecting refrigerant pressures and provides approximate conditions.
Table detailing operating pressures for GE units during cooling and heating cycles.
Table defining cooling water pressure drops in feet of head for GE and EX units.
Presents heating water pressure drops in feet of head for GE units.
Table providing water volume in cubic inches, feet, and gallons for GE and EX units.
Outlines suggested preventive maintenance tasks, including filter inspection and water quality checks.
Table showing filter sizes in inches and millimeters for various unit models.
Table specifying acceptable water quality parameters for heat exchangers.
Emphasizes maintaining a primed condensate trap for proper operation and preventing issues.
Explains the function of diagnostic LEDs on deluxe control boards for troubleshooting.
Lists common operational problems, causes, and suggested corrections for unit issues.
Table detailing wiring for Honeywell isolation valves for different control types.
Wiring diagrams for basic 24V systems across various voltages and phases.
Wiring diagrams for deluxe 24V systems across various voltages and phases.
Wiring diagrams for Tracer ZN510 systems across various voltages and phases.
Wiring diagrams for Tracer ZN524 systems across various voltages and phases.
Details Trane's standard parts-only warranty duration and conditions.
Describes the optional extended warranty coverage and its applicability.
General
