Vectronix BT PLRF25C - User Manual

Questions and Answers

L
loripowellAug 18, 2025
What to do if 'BATT LOW' is displayed on Vectronix BT PLRF25C?
- B
  brianwalkerAug 18, 2025
  If the Vectronix Measuring Instruments displays 'BATT LOW', it means the battery is almost depleted. Replace the battery to resolve this.
R
Richard EspinozaAug 20, 2025
Why does my Vectronix BT PLRF25C measure objects in front or behind the intended object?
- R
  Robert LarsonAug 20, 2025
  If the Vectronix Measuring Instruments measures objects in front or behind the intended object, it is because '3DIS OF' is selected in the configuration menu. To fix this, select '3DIS ON' in the configuration menu.
G
galvaradoAug 23, 2025
Why are my Vectronix BT PLRF25C Measuring Instruments not working at all?
- A
  Andrew LewisAug 23, 2025
  If your Vectronix Measuring Instruments are not functioning at all, the possible causes are: 1. The battery has run out: Replace the battery. 2. Battery contacts corroded: Clean the battery contacts. 3. Low temperature: Warm up the battery. 4. Extreme heat: Do not store the battery at temperatures over +70°C. 5. The device is defective: Contact customer support.
A
Anthony BennettAug 26, 2025
What to do if Vectronix Measuring Instruments displays 'D----' after distance measurement?
- C
  Christopher TorresAug 26, 2025
  If the Vectronix Measuring Instruments displays 'D----' after distance measurement, it could be due to the distance being outside the specified range or the object being too small or inaccurately targeted. Make sure to respect the specified measurement range and factors affecting measurement range.
D
Deborah AguilarAug 28, 2025
Why are the azimuth values inaccurate on my Vectronix BT PLRF25C Measuring Instruments?
- C
  Charles LangAug 28, 2025
  If the Vectronix Measuring Instruments displays 'Inaccurate azimuth values', this could be due to: 1. Incorrect declination setting: Set the correct declination. 2. Disruptive magnetic fields: Respect factors affecting azimuth measurement accuracy. 3. Bad calibration or altered magnetic conditions: Perform compass calibration.
J
juanjohnstonAug 30, 2025
What does 'AZI----' mean on Vectronix BT PLRF25C Measuring Instruments?
- D
  David FordAug 30, 2025
  If the Vectronix Measuring Instruments displays 'AZI----', it means the tilt angle is outside the specified range or the digital magnetic compass is damaged. Respect the specified tilt angles. If the issue persists, contact customer support.
T
Tiffany HebertSep 2, 2025
Why does Vectronix BT PLRF25C display 'NVIS ON' after a measurement?
- C
  Clifford ZamoraSep 2, 2025
  If 'NVIS ON' is displayed after a measurement on Vectronix Measuring Instruments, it means the device is being used during daylight conditions with 'NVIS ON' selected in the configuration menu. Select 'NVIS OF' in the configuration menu to resolve this.
C
Carmen GarzaSep 4, 2025
What does 'INC----' mean on Vectronix Measuring Instruments?
- S
  Stacy LambertSep 4, 2025
  If the Vectronix Measuring Instruments displays 'INC----', it indicates that the tilt angle is outside the specified range or the tilt sensors are damaged. Respect the specified tilt angles. If the issue persists, contact customer support.
S
sean42Sep 7, 2025
How to fix compass calibration that cannot be completed on Vectronix BT PLRF25C Measuring Instruments?
- D
  Dillon HudsonSep 7, 2025
  If the compass calibration cannot be completed on your Vectronix Measuring Instruments, it is likely due to timing out of calibration. Follow the instructions slightly faster to resolve this issue.
J
James HuberSep 9, 2025
What does 'D GATED' mean on Vectronix Measuring Instruments after distance measurement?
- A
  Alexandra CharlesSep 9, 2025
  If the Vectronix Measuring Instruments displays 'D GATED' after distance measurement, it means the measured distance is below the selected distance gate. Reduce or turn off the distance gate to solve this issue.